Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly. . . * . . . . . aus Washing the dishes Aqua sensor * * depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3–6 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. Switching on the appliance Turn on the tap fully. Open the door. Switch on ON/OFF switch 1 . The display of the last selected programme flashes. This programme remains selected if no other programme button 2 is pressed. The expected programme duration flashes on the digital display 3 . Press the START button 9 . Close the door. The programme starts running. Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display 3 . The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). Display window Apart from information on the programme sequence, the display window 11 also indicates additional information on e.g. glass protection system is active. If you would no longer like to have this additional information displayed, proceed as follows. Open the door. Switch on ON/OFF switch 1 . Hold down programme button A and press START button 9 until on the digital display is indicated. Release both buttons. Press programme button A until the factory set value is indicated on the digital display 3 . To change the setting, By pressing the C button, you can switch the onboard computer (additional programme information) off or on . Press START button 9 . The set value is saved. Close the door. Timer programming You can delay the start of the programme in 1-hour steps up to 24 hours. Open the door. Switch on ON/OFF switch 1 . Press 7 + button until the timer programming display 6 jumps to . Press 7 + or – button until the displayed time corresponds with your requirements. Press START button 9 , timer programming is activated. To delete timer programming, press the 7 + or – button until is indicated on the digital display 6 . You can change your programme selection at any time until the programme starts. Close the door. aus End of programme The programme has ended when the value is indicated on the numerical display 3 . The end of the programme is also indicated by an acoustic signal. This function can be changed as follows: Open the door. Switch on ON/OFF switch 1 . Hold down programme button A and press START button 9 until on the digital display is indicated. Release both buttons. Press programme button A until the factory set value is indicated on the digital display . To change the setting, press programme button C . Each time the button is pressed, the set value increases by one level; when the value of has been reached, the display jumps back to (off). Press START button 9 , the set value is saved. Close the door. Automatic switch off when programme ends To save energy, the dishwasher is switched off 20 minutes after the programme ends. This function can be changed as follows: Open door. Switch on ON/OFF switch 1 . Hold down programme button A and press START button 9 until is indicated on the digital display. Release both buttons. Press programme button A until the factory set value 3 is indicated on the digital display . To change the setting: Press the button C to switch the function off or on . Press START button 9 . The set value is saved. Close door. Switching off the appliance Short time after the end of the programme: Open the door. Switch off ON/OFF switch 1 . Turn off the tap (not applicable if Aqua-Stop fitted). Remove the utensils when they have cooled down. Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme Open the door. Switch off ON/OFF switch 1 . The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. To continue the programme, switch on the ON/OFF switch 1 again. Close the door. Terminating the programme (Reset) Open the door. Press START button 9 for approx 3 sec. is indicated on the digital display 3 . Close the door. The programme sequence lasts approx. 1 min. is indicated on the digital display...