Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Individual positions are referred to in the text. Control panel 1 2 3 4 5 6 7 8 9 10 11 ON/OFF switch Programme buttons ** Digital display Display “Check water supply” Salt refill indicator Rinse-aid refill indicator Timer programming display Time delay Additional options ** START button Door Opener ** Number depending on model Appliance interior 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Interior light * Top basket Knife shelf * Tablet collecting tray Top spray arm Bottom spray arm Dispenser for salt Filters Cutlery basket Bottom basket Dispenser for rinse aid Detergent dispenser Lock for detergent dispenser Rating plate * depending on model en Water softening system To ensure good washing results, the dishwasher requires soft water, i.e. containing low amounts of lime, otherwise white limescale will be deposited on the utensils and inner container. Tap water above 7 dH (from set value ) must be softened. The water is softened with salt (regeneration salt) in the water softening system of the dishwasher. The setting and therefore the required amount of salt depends on the degree of hardness of your tap water (see table). Set The amount of salt dispensed can be set from to . Sal is not required at the set value . Find out about the hardness value of your tap water. Your water supply company will assist you. Set value can be found in the water hardness table. Open the door. Switch on ON/OFF switch 1 . Hold down programme button A and press START button 10 until on the digital display is indicated . Release both buttons. The LED for button A flashes and the digital display displays the factory setting . To change the setting, press programme button C . Each time the button is pressed, the set value increases by one level; when the value of has been reached, the display jumps back to (off). Press START button 10 . The chosen setting has now been stored. Close the door. Water hardness table en Salt Using salt Always refill with salt immediately before switching on the appliance. This ensures that overrun salt solution is immediately washed out and does not corrode the rinsing tank. Open the screw-type cap of the compartment 26 . Fill the tank with water (only required when switching on the appliance for the first time). Then add dishwasher salt (not table salt or tablets). The water is displaced and runs out. As soon as the salt refill indicator on the fascia is lit, top up the salt. 5 Switching off salt refill indicator/water softening system If the salt refill indicator 5 is impaired (e.g. when using combined detergents containing salt component), it can be switched off. Proceed as described under “Setting water softening system” and set the value to . The water softening system and salt refill indicator are now switched off. Warnings Never fill the salt dispenser with detergent. You will destroy the water softening system. To prevent corrosion, always refill with salt immediately before switching on the appliance. * depending on model Using detergents with salt component If combined detergents with a salt component are used, salt can usually be omitted up to a water hardness of 21 dH (37 fH, 26 Clarke, 3.7 mmol/l). If the water hardness is over 21 dH, salt must be used. en Rinse aid As soon as the rinse-aid refill indicator lights up on the control panel, refill with rinse aid. The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers. Combined detergents with rinse-aid component may be used up to a water hardness of 21 dH (37 fH, 26 Clarke, 3,7 mmol/l) only. If the water hardness is over 21 dH, rinse-aid must be used. Open the dispenser 30 by pressing and lifting the plate on the cover. Carefully pour rinse aid up to the max. mark in the filler opening. Close cover until it clicks shut. To prevent excessive foam formation during the next rinse cycle, remove any rinse aid which has run over with a cloth. Setting amount of rinse-aid The amount of rinse-aid dispensed can be set from to . The factory setting is . Do not change the amount of rinse-aid unless streaks (select lower setting) or water stains (select higher setting) are left on the utensils. Open the door. Switch on ON/OFF switch 1 . Hold down programme button A and press START button 10 until on the digital display is indicated . Release both buttons. The LED for button A flashes and the digital display displays the factory setting . Press programme button A until the factory set value is indicated on the digital display 3 . To change the setting, press programme button C . Each time the button is pressed, the set value increases by one level; when the value of has been reached, the display jumps back to (off). Press START button 10 . The set value is saved. Close the door. Switching off rinse-aid refill indicator If the rinse-aid refill indicator 6 is impaired (e.g. when using combined detergents containing rinse-aid component), it can be switched off. Proceed as described under “Setting amount ...
Este manual também é adequado para os modelos :Máquinas de lavar louça - SMVATT01NL/01 (2.56 mb)