Pull the mains plug out of the wall socket, cut through the connecting cable and disable the door lock. Take the appliance to a designated waste disposal centre. Warning Children could get locked in the appliance (risk of suffocation) or get stuck in other positions. Therefore: Remove the mains plug, cut the mains wire and set aside. Damage the door lock so that the door can no longer be closed. en Getting to know your appliance Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front. Individual positions are referred to in the text. Control panel 1 Programme selector 2 Start position 3 Programme sequence indicator 4 Door handle 5 Main switch (ON/OFF) 6 Programme overview 7 Indicator light Appliance interior 20 Upper spray arm 21 Top basket with additional cup rack * 22 Lower spray arm 23 Filters 24 Bottom basket 25 Container for special salt with level indicator * 26 Switch for setting water hardness 27 Cutlery basket 28 Container for rinse-aid, with refill indicator 29 Detergent dispenser 30 Locking mechanism 31 Nameplate * not on all models You will need to purchase the following before using the dishwasher for the first time: – special salt for use in dishwashers – detergent – rinse-aid Only use products, which are suitable for dishwashers. Water softener In order to rinse dishes and glasses satisfactorily, the dishwasher requires soft water, i.e. containing little or no lime, otherwise water stains will be left behind on crockery and glasses, etc. If the tap water exceeds a certain level of hardness, it must be softened, i.e. decalcified, so that it can be used in the dishwasher. This is achieved by adding a special salt to the water softener inside the dishwasher. The water softener, that is the required amount of salt, is set up according to how hard the tap water is. Setting up the water softener (see introduction) en Filling the special salt container How the salt works While washing is taking place, salt is automatically rinsed out of the salt container into the water softener where it dissolves the lime in the water. The dissolved lime is pumped out of the dishwasher. The water softening system is then ready for the next load. This process of regeneration can only function when the salt is dissolved in water. Unscrew the lid on the salt container 25 . Before you use the dishwasher for the first time, pour approx. 1 litre of water into the salt container. Place the funnel supplied with the dishwasher in the filler hole. Tip in enough salt to fill the container to the top (maximum of 1.5 kg). As you tip in salt, some of the water is displaced and drains away. When you have done this, clean off any remnants of salt from the area round the neck of the container. Screw the lid back onto the container, ensuring that it is not cross-threaded. Note If the switch is set to ”0”, it is not necessary to add any salt, as none is consumed while the dishwasher is operating. If the switch is set between ”1” and ”3”, then salt must be added. Do not pour detergent into the container for special salt. This would destroy the water softener. LOW SALT indicator Salt should be added as soon as the coloured dot in the lid on the salt container 25 is no longer visible. en Filling the rinse-aid container The purpose of a rinse-aid is to prevent the formation of water marks on tableware and utensils, and to ensure that glasses are clean and sparkling. The rinse-aid is consumed during the washing process. Fold back the lid on the rinse-aid container 28 . To open the lid, press the mark on the rinse-aid lid and simultaneously lift the lid off the lug . Pour the rinse-aid into the filler hole until the level indicator turns dark. Close the lid, ensuring that you hear it snap closed. Note Use only rinse aid for domestic dishwashers. Spilt rinse aid may result in excessive foam formation in the next rinse cycle. Therefore, remove any spilt rinse aid with a cloth. Adjusting the amount of rinse-aid The amount of rinse-aid added to the water can be varied by adjusting the stepless control. The rinse-aid control has been set to ”4” in the factory. Do not alter the setting of the rinse-aid control unless streaks (turn knob towards ”–”) or water marks (turn knob towards ”+”) are left on the dishes. 28 rinse–aid control LOW RINSE-AID indicator As long as the LOW RINSE-AID indicator on the dispenser 28 is dark, there is sufficient rinse-aid in the dishwasher. LOW RINSE-AID indicator en Unsuitable dishes You should not clean the following items in your dishwasher: Cutlery and dishes made of wood. They will leach out and become unsightly; the utilised adhesives are also not suitable for the dishwasher temperatures. Delicate decor glasses, craft dishes and vases, special antique or irreplaceable dishes. These decor items are not dishwasher-safe. Plastic parts, copper and tin dishes sensitive to hot water are not suitable either. Overglazed patterns, aluminium and silver parts tend to becom...

Este manual também é adequado para os modelos :
Máquinas de lavar louça - SGIAIA8/70 (2.35 mb)
Máquinas de lavar louça - SGIAIA9/58 (2.35 mb)
Máquinas de lavar louça - SGIAIA9/70 (2.35 mb)
Máquinas de lavar louça - SGIAIB1/58 (2.35 mb)