Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Switching the salt refill indicator / water softening system off and on Hold down the programme button B and switch on the main switch 1 , then release the buttons. The illuminated button B and the factory-set value on the digital display flash. To change the setting: press the programme button B . Each time the button is pressed, the set value increases by one; when the value is reached, the display jumps back to (the salt refill indicator / water softening system has been switched off). Switch off the main switch 1 . The set value is stored within the device. Approx. 4 litres of water are required to regenerate the water softening system. As a result, the water consumption per rinse cycle increases by 0 to maximum 4 litres depending on the water hardness setting. Note If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid refill indicator has been switched on and the water softening system has been set to the correct water hardness. en Programme overview This overview lists the max. possible number of programmes. The programmes supplied with your appliance are indicated on the fascia. Type of crockery e.g.china, pots/pans, Mixed cutlery, glasses, etc. Nondelicate Mixed Delicate Type of food remains Amount of food remains Condition of food remains Soups, casseroles, sauces, potatoes, pasta, rice, eggs, roast or fried food Soups, potatoes, pasta, rice, eggs, roast or fried food Coffee, cakes, milk, sausage, cold drinks, salads Rinse off if the dishes have been stacked for several days in the dishwasher prior to washing. a lot a little very little stuck on hard loosely attachedmedium Wash programme Programme sequence Auto 55°.65° Intesive 70° Drying Drying DryingEco 50° Quick 35° Pre-rinse Rinse-aid 70° Main rinse Main rinse Rinse-aid 55° Wash 35° Rinse-aid 65° Wash 50° Pre-rinse Gentle 40° Pre-rinse Wash 40° Main rinse Rinse-aid 55° Drying Third rinse Pre-rinse 50° Wash 70° First rinse Second rinse The programme sequence isoptimized and adapted with howthe appliance is loaded and howdirty the dishes are. Pre-rinse Programme selection The most appropriate programme can be identified by comparing the type of crockery, cutlery, etc., as well as the amount and condition of food remains, with the details contained in the programme overview. You will find the appropriate programme information in the introduction. en Washing dishes Reduce costs! If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Programme data The stated programme data are based on standard operating conditions. The values can vary considerably according to: different amounts of dishes temperature of mains water supply pressure of mains water supply ambient temperature fluctuations in mains voltage machine-related factors (e.g. temperature, water volume, ...). Energy and water consumption is reduced by up to 1/4 when dishes are washed in the upper basket only. Water consumption values are based on a water hardness setting of 4. Aqua sensor * * on applicable models The Aqua sensor is an optical measuring device which measures the turbidity of the rinsing water. A light barrier can detect dissolved food remnants in the water, e.g. egg, fat and oats. The Aqua sensor is used according to the programme. When the Aqua sensor is active, ”clean” rinsing water may be transferred into the next rinsing bath and/or the temperature adjusted. If the turbidity is greater, the water is drained and is replaced with fresh water. In this way the water consumption is reduced by approx. 4 litres for utensils which are ”less” dirty. Switching the dishwasher ON Turn on the tap. Set main switch 1 to ON. Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 6 is pressed The numerical display 8 shows the expected duration of the programme. Close door. The programme starts automatically. Programme sequence indicator 9 Your dishes are being cleane Your dishes are being rinsed. Your dishes are being dried. Optical indicator during operation * * With some models During the rinse programme a light point appears on the floor below the device’s door. Only open the dishwasher door when the light point has disappeared. In the case of built-in dishwashers with flush front the light point will not be visible. End of programme The end of the programme is indicated by a buzzer. This function can be changed as follows:– Hold down Function button C pressed and switch on main switch , then let the buttons go. Function Button C flashes, and the digital display indicates the value which was set at the factory (semi-loud). To change the setting: Press Function button C . Each depression of the button increases the set value by one, when is reached, the display jumps back to (off). Switch off the main switch 1 . The set ...
Este manual também é adequado para os modelos :Máquinas de lavar louça - SGU67T05TC/06 (2.59 mb)
Máquinas de lavar louça - SGU67T05TC/07 (2.59 mb)