Assessments - 3, GPA: 4.3
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
General Built-under and integrated appliances which are subsequently installed as free-standing appliances must be secured to prevent them from falling over, e.g. by screwing them to the wall or by installing them under a continuous worktop which is screwed to the adjoining units. For Swiss version only: The appliance can be installed without difficulty between wooden and plastic walls in a kitchen range. If the appliance is not connected via a plug, the installation side must feature an all-pole disconnector with a contact gap of at least 3 mm in order to satisfy the relevant safety regulations. Installation The dishwasher must be connected by a qualified technician to ensure correct operation. The specifications for supply, drainage and connected load must fulfil the required criteria as stated in the following paragraphs or in the installation instructions. Install the appliance in the following sequence: – Check the delivery – Install the appliance – Connect the waste water – Connect the fresh water – Connect the power supply Delivery Your dishwasher was checked at the factory to ensure that it was in perfect working order. This may have left some small water stains in the dishwasher. These will disappear after the first rinse cycle. Installation The required installation dimensions can be found in the installation instructions. Using the height-adjustable feet, adjust the appliance until it is level. Ensure that the appliance is standing firmly. Waste water connection See the installation instructions for the required connection steps. If required, attach a siphon with drainage spigot. Using the enclosed parts, connect the waste water hose to the drainage spigot of the siphon. Ensure that the drainage hose is not kinked, crushed or twisted (ensure that there is no sealing cover which prevents the waster water from flowing away!). en Fresh water connection Using the enclosed parts, connect the fresh water connection to the tap according to the installation instructions. Ensure that the fresh water connection is not kinked, crushed or twisted. When replacing the appliance, always connect a new water supply hose to the water supply. The old supply hose must not be re-used. Water pressure: Minimum 0,05 MPa (0,5 bar) – maximum 1 MPa (10 bar). If the water pressure is higher, install a pressure reducing valve. Flow rate: Minimum of 10 litres per minute. Water temperature: We recommend that you use cold water. If you do use hot water, the temperature should not exceed 60 °C. Electrical connection Connect the appliance only to 230 V alternating current via a correctly installed socket with protective conductor. See rating plate for required fusing 31 . The socket must be attached near the dishwasher and be freely accessible. The connection may be modified by an electrician only. Use only a residual-current-operated circuit-breaker which features the symbol. Only this circuit breaker guarantees compliance with the currently valid regulations. Removing the appliance It is essential, when removing the appliance, to observe the following sequence: First, disconnect the appliance from the power supply. Pull out the mains plug. Turn off the water supply. Disconnect the waste water and fresh water connections. Loosen the fastening screws under the worktop. If fitted, remove the base panel. Pull out the appliance, carefully pulling the hose behind. Transporting the dishwasher Drain water from the dishwasher. Secure all loose parts. The appliance should only be transported in an upright position. If the appliance is not kept upright during transport, any water left inside may seep into the control module and cause subsequent errors with programme functions. The appliance must be drained in the following sequence: Turn on the tap. Set main switch to ON. Select the B programme. The programme duration in minutes is shown in the numerical display. Close the door. Wait for approximately 4 minutes. Terminate the programme by pressing A and C simultaneously. The time display changes to . Close the door. Wait a further minute and then switch the appliance off. Turn off the tap. en Protection from freezing temperatures If the appliance is installed in a location where there is a risk of freezing temperatures (e.g. in a holiday home), all water must be complete...
Este manual também é adequado para os modelos :Máquinas de lavar louça - SGV46M43EU/82 (2.51 mb)
Máquinas de lavar louça - SGV46M43EU/86 (2.51 mb)
Máquinas de lavar louça - SGV46M43EU/93 (2.51 mb)
Máquinas de lavar louça - SGV46M43EU/94 (2.51 mb)