Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Máquinas de lavar louça - SHE43RP2UC/64 (2.67 mb)
Máquinas de lavar louça - SHE43RP2UC/64 (3.41 mb)
Facilidade de uso
Lift the assembly out. Carefully examine the assembly. If you find debris in the Large Object Trap, turn it upside-down and gently tap it on a flat surface to dislodge and remove debris. 17 Remove the Micro Filter as shown in Figure 13 on page 16. Flush the Micro Filter and Fine Filter clean by holding them under running water. To reinstall the filter system, return the Micro Filter to the installed position. Place the Large Object Trap/Cylinder Filter Assembly and Fine Filter into the installed position. Turn the locking nut clockwise until it is locked. The arrow on the ring handle and the arrow on the Fine Filter should point at each other. Clean the exterior door panel Colored doors: use only a soft cloth dampened with soapy water. Stainless steel doors: use a soft cloth with a non-abrasive cleaner (preferably a liquid spray) made for cleaning stainless steel. For the best results, apply the stainless steel cleaner to the cloth and then wipe the surface. Clean the door gasket Regularly clean the door gasket with a damp cloth to remove food particles and other debris. Also clean the door seal, located inside the dishwasher at the bottom of the door. Winterizing your unit If your dishwasher will be unused for an extended period of time in a location that experiences freezing temperatures (holiday home or through a vacation period), have your dishwasher winterized by an authorized professional service. Turn your household water supply to the dishwasher off when on extended vacation or when dishwasher will not be used for more than 1 month. 18 Self Help Dishwashers may occasionally exhibit problems that are unrelated to a malfunction of the dishwasher itself. The following information may help you with a dishwasher problem without involving a repair professional. Problem Cause Action Dishwasher does not start 1. Door may not be properly latched 2. Unit may not be turned on 3. Unit not reset or previous cycle not completed 4. Delay start engaged 5. Interruption of electrical power supply to dishwasher or blown fuse. 6. The door may have been closed without first selecting a cycle 7. Water supply may not be turned on 1. Shut the door completely until you hear it click. 2. Press the main power switch to turn unit on. 3. To reset, refer to “Cancel a Cycle” (page 15) in this manual. 4. To reset, refer to “Delay Start” (page 15) section in this manual. 5. Check circuit breaker 6. Select a cycle and close the door. 7. Check and turn on water supply. Dishwasher beeping (end of cycle signal) 1. Default factory settings alert the customer that the cycle is complete by beeping. This feature can be deactivated if so desired. 1. To adjust the volume or deactivate, refer to the “Cycle Completion Signal” (page 15) section in this manual. Display does not illuminate 1. A fuse may have been blown or circuit breaker tripped 2. Door not closed or latched Note: For models with controls on top of the door, the display only illuminate when the door is opened and controls are visible. 1. Check the fuse or circuit breaker box and replace the fuse or reset the breaker if necessary 2. Ensure door is properly latched and completely closed Dishwasher seems to run a long time 1. Incoming water is not warm enough 2. Cycle time can vary due to soil and water conditions 3. Rinse agent dispenser is empty 4. Dishwasher connected to cold water supply Note: Refer to “Wash Cycle Information” section in this manual for typical cycle lengths 1. Before starting a cycle, run hot water faucet at the sink closest to the dishwasher 2. Sensors in the dishwasher automatically increase the cycle time to ensure a good wash when heavy soil is detected 3. Add rinse agent 4. Verify dishwasher is connected to hot water supply plumbing Dishes are not getting clean enough 1. Spray arm movement obstructed 2. Spray arm nozzles clogged 3. Improper use of detergents 4. Filters could be clogged 5. Dishes are nested or loaded too close together 6. Selected wash cycle is not suitable for food soil conditions 1. Ensure that spray arm movement is not blocked by hand rotating spray arms before starting cycle 2. Remove the spray arms and clean according to the “Care and Maintenance” (pages 16-17) section of the manual 3. Increase or decrease detergent depending on the water hardness (refer to Table 1 on page 12) 4. Clean the filters according to the “Care and Maintenance” (pages 16-17) section of the manual 5. Rearrange load such that water spray can reach all items in the dishwasher - see “Loading the Dishwasher” (page 7) section of the manual 6. Refer to “Wash Cycle Information” (page 14) section of the manual Dishes are not getting dry enough 1. Rinse agent dispenser is empty 2. Improper loading of dishes 3. Selected cycle does not include drying 4. Extra Dry Heat is not activated Note: Plastic or Teflon do not typically dry as well as other items due to their inherent properties 1. Add rinse aid - the use of rinse aid improves drying 2. Rearrange load to ensure items...
Este manual também é adequado para os modelos :Máquinas de lavar louça - SHE43RP5UC/64 (2.53 mb)
Máquinas de lavar louça - SHE43RP6UC/64 (2.53 mb)
Máquinas de lavar louça - SHV43R53UC/64 (2.53 mb)
Máquinas de lavar louça - SHV55R53UC/64 (2.53 mb)