Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Be careful of hot water that may splash out. 2 Press and hold the two buttons labeled Cancel/Reset for 3 seconds. 3 Close the door and wait about 1 minute while the dishwasher drains. 4 Open the door and press the On/Off button. You may now start a new cycle. WARNING You could be seriously scalded if you allow hot water to splash out of the dishwasher. OPEN THE DOOR CAREFULLY during any wash or rinse cycle. Do not fully open the door until water noises have stopped. Interrupt a cycle: 1 Open the dishwasher door just far enough to expose the control panel. Be careful of hot water that may splash out. 2 Press the On/Off button to turn the unit off. 3 Wait at least 10 seconds before fully opening the dishwasher door. 4 To resume the cycle, press the On/Off button and close the dishwasher door. Table 2 - Wash Cycle Information Heavy Wash Auto Wash Normal Wash Delicate Wash Express Wash Rinse & Hold cycle time 135 min 95-119 min 115 min 80 min 30 min 9 min cycle time with Half Load 115 min 99 min 90 min not available not available not available cycle time with Sanitize 135 min 105-135 min 125 min not available not available not available water consumption 23.2-27.4 L 6.1-7.2 gal 10.4-22.5 L 2.7-5.9 gal 8.9-18.3L 2.4-4.8 gal 13.1 L 3.5 gal 13.1 L 3.5 gal 4.7 L 1.2 gal wash temperature 66-72°C 151-162°F 55-72°C 126-162°F 50-69°C 122-156°F 50°C 122°F 45-72°C 113-162°F no wash rinse temperature 72°C 162°F 65-72°C 156-162°F 45-69°C 113-156°F 69°C 156°F 50°C 122°F incoming water temp. 13 Extra Dry Heat: 1 Press and hold the Auto button, then press and hold the On/Off button. 2 When the LED display window indicates a “0” or “1” release both buttons. 3 To activate Extra Dry Heat, press the Auto button until the display indicates “1”. 4 To disable Extra Dry Heat, press the Auto button until the display indicates “0”. 5 Press the On/Off button to save the setting. Cycle completion signal: The cycle completion signal alerts you when a cycle completes and the dishwasher has washed and dried the dishes. You can choose to disable the tone or adjust the volume. To activate: 1 With the unit OFF, press and hold the right of the two Cancel/Reset buttons and then press and hold the On/Off button. 2 When the light on the Cancel/Reset button you are pressing illuminates and the tone goes off, release both buttons. 3 Press the right of the two Cancel/Reset buttons again until you achieve the desired volume or until there is no tone (to turn cycle completion signal OFF). 4 Press the On/Off button to save the setting. SHE68R5xUC and SHX68R5xUC front display key: Check water inlet Sensors OK Spray pressure Do not open door Sanitation rinse Wash Rinse Dry Program progress 14 Figure 9 Figure 10 Trap Filter Large Object Cylinder Fine Filter Figure 11 Micro Figure 12 Filter Care and Maintenance Maintenance Tasks Certain areas of the dishwasher require occasional maintenance. The maintenance tasks are easy to do and will ensure continued superior performance from your dishwasher. Wiping up spills and splash-outs Water may occasionally splash out of your dishwasher, particularly if you interrupt a cycle or open the dishwasher door during a cycle. To avoid floor damage and possibly mold growth, do not allow wet areas to remain around or under the dishwasher. Clean the stainless steel inner door and tub Clean the outer edges of the inside door panel regularly to remove debris that may collect from normal loading. If spots begin to appear on the stainless steel, make sure the rinse agent is full and functioning properly. Check and clean spray arm nozzles Remove the top spray arm by first removing the empty top rack from the dishwasher. Turn the rack upside down. The top spray arm is held in position by a locking nut as shown in Figure 9. Turn the locking nut counterclockwise and remove it to release the spray arm. Look for obstruction in the spray nozzles. If the spray nozzles need cleaning, flush them under running water. To reinstall the top spray arm, place it back in position and return the locking nut to its install position. Turn the locking nut clockwise to secure. Return the top rack to the top rack roller guides. Remove the bottom spray arm by first removing the empty bottom rack from the dishwasher. Grasp and lift the spray arm as shown in Figure 10. Look for obstruction in the spray nozzles. If the spray nozzles need cleaning, flush them under running water. To reinstall the bottom spray arm, return the bottom spray arm to the installed position and press it until it snaps into place. Return the bottom rack to the installed position. Check and clean the filter system The filter system consists of a Large Object Trap/Cylinder Filter assembly, a Fine Filter and a Micro Filter. The filter system is located on the inside of your dishwasher under the lower rack an is easily accessible. During normal use, the filter system is self-cleaning. You should occasionally inspect it for foreign objects and clean it when necessary. CAUTION To avoid ...
Este manual também é adequado para os modelos :Máquinas de lavar louça - SHE68R55UC/63 (1.75 mb)
Máquinas de lavar louça - SHE68R56UC/63 (1.75 mb)
Máquinas de lavar louça - SHV68R53UC/63 (1.75 mb)
Máquinas de lavar louça - SHX68R52UC/63 (1.75 mb)