|
Facilidade de uso
Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. . To ensure that the door seal always remains clean and hygienic, regularly clean it with a damp cloth and a little washing-up liquid. . If the appliance is switched off for a prolonged period, leave the door ajar to prevent the formation of an unpleasant odour. Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. a Warning – Health hazard Never use other domestic detergents, e.g. containing chlorine! Rinse aid . Check the refill indicator `. If required, refill rinse aid. Filters The filters 1J keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter, a flat fine filter and a microfilter. 1. After each washing cycle check the filters for residue. 2. Unscrew filter cylinder as illustrated and take out filter system. 3. Remove any residue and clean filters under running water. 4. Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system. Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 1: and 1B. 1. Check outlet nozzles on the spray arms for blockages. 2. Unscrew the upper spray arm 1:. 3. Remove the lower spray arm 1B upwards. 4.Clean spray arms under running water. 5.Re-engage or screw on spray arms. Fault, what to do? aus 3 Fault, what to do? Experience has shown that you can rectify most faults which occur in daily operation yourself. This ensures that the machine is quickly available to you again. In the following overview you can find possible causes of malfunctions and helpful information for rectifying them. Note If the appliance stops during dishwashing or does not start for no obvious reason, first run the Abort programme function (Reset). (See chapter entitled “Operating the appliance”) a Warning – Don’t forget: Repairs may be carried out by technicians only. If a component has to be replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at considerable risk. aus Fault, what to do? Waste water pump 7. Place cover in the original position and press down until it engages (click). Large food remnants or foreign objects which were not captured by the filters may block the waste water pump. The rinsing water will then be above the filter. In this case: 1. First always disconnect the appliance from the power supply. 2. Take out top basket 1" and bottom basket 1Z. 3. Remove the filters 1J. 4. Scoop out water, use a sponge if required. 5. Prise out the white pump cover (as illustrated) using a spoon. Grip the cover on the crosspiece and lift diagonally inwards. Remove cover completely. 8. Install filters. 9. Re-insert baskets. 6. Check impeller wheel and remove any foreign objects. Fault, what to do? aus Fault table Fault Cause Remedial action “Check water supply” display X lights up. Supply hose kinked. Tap turned off. Tap jammed or calcified. Filter in the water supply blocked. Install supply hose without kinks. Turn on the tap. Turn on the tap. Flow rate must be min. 10 l/min. when water supply is open. Switch off the appliance and pull out the mains plug. Turn off the tap. Unscrew water connection. Clean filter in the supply hose. Screw water connection on again. Check for leaks. Reconnect power supply. Switch on the appliance. Error code “:.. is lit. Error code “:.… is lit. Filters 1J are soiled or blocked. Waste water hose is blocked or kinked. Clean filters. (See Cleaning and maintenance) Install hose without kinks, remove any residue. Siphon connection still sealed. Check connection to siphon and open if required. Error code “:.† is lit. Error code “:.. is lit. Cover on the waste water pump loose. Waste water pump blocked or cover on the waste water pump is not locked in position. Mains voltage too low. Lock cover correctly. (See Waste water pump) Clean pump and lock cover correctly. (See Waste water pump) Not an appliance fault, have the mains voltage and electrical installation checked. aus Fault, what to do? Fault Cause Remedial action A different error code is indicated on the digital display. A technical fault has probably occurred. Switch off appliances with the ON/OFF switch...
Este manual também é adequado para os modelos :Máquinas de lavar louça - SMS63L08AU/09 (1.94 mb)
Máquinas de lavar louça - SMS63L08AU/13 (1.94 mb)
Máquinas de lavar louça - SMS63L08AU/18 (1.94 mb)