Assessments - , GPA:
(
)
)
Fabricante : Bosch
Arquivo Tamanho: 1.95 mb
Arquivo Nome :
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
por este dispositivo também tem outras instruções :
Facilidade de uso
The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3–6 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. Switching on the appliance – Turn on the tap fully. – Open the door. – Switch on ON/OFF switch (. The display of the last selected programme flashes. This programme remains selected if no other programme button 0 is pressed. The expected programme duration flashes on the digital display h. – Press the START button `. – Close the door. The programme starts running. en Optical display while the programme is running * * depending on model While the programme is running, a light spot shines on the floor under the appliance door. Do not open the dishwasher door until the light point is no longer visible on the floor. If the appliance is installed at eye-level, with flush furniture front, the light point is not visible. This function can be changed as follows: – Open the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display. – Release both buttons. The LED for button # flashes and the digital display h displays the factory setting •:‹…. – Press programme button # until the factory set value ‚:‹‚ is indicated on the digital display h. To change the setting: – By pressing the button 3, you can switch the function off ‚:‹‹ or on ‚:‹‚. – Press START button `. The set value is saved. – Close the door. Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display h. The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). Timer programming * * depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. – Open the door. – Switch on ON/OFF switch (. – Press button P + until the digital display h jumps to oe:‹‚. – Press P + or – button until the displayed time corresponds with your requirements. – Press START button `, timer programming is activated. – To delete timer programming, press the P + or – button until h oe:‹‹ is indicated on the digital display. You can change your programme selection at any time until the programme starts. – Close the door. End of programme The programme has ended when the value ‹:‹‹ is indicated on the numerical display h. The end of the programme is also indicated by an acoustic signal. This function can be changed as follows: – Open the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display. – Release both buttons. The LED for button # flashes and the digital display h displays the factory setting •:‹…. – Press programme button # until the factory set value ›:‹. is indicated on the digital display h. To change the setting, – Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of ›:‹„ has been reached, the display jumps back to ›:‹‹ (off). – Press START button `, the set value is saved. – Close the door. en Switching off automatically after the end of the programme * * depending on model To save energy, the dishwasher is switched off 1 minute after the programme ends (factory setting). Automatic disconnection can be adjusted from .:‹‹ to .:‹.. .:‹‹ Appliance does not switch off automatically .:‹‚ Off after 1 min .:‹. Off after 120 min – Open the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button ` until •:‹... is indicated on the digital display. – Release both buttons. The LED for button # flashes and the digital display h displays the factory setting •:‹…. – Press programme button # until the factory set value .:‹‚ is indicated on the digital display h. To change the setting: – Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of .:‹. has been reached, the display jumps back to .:‹‹ (off). – Press START button `. The set value is saved. – Close the door. Switching off the appliance Short time after the end of the programme: – Open the door. – Switch off ON/OFF switch (. – Turn off the tap (not applicable if Aqua- Stop fitted). – Remove the utensils when they have cooled down. a=Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme – Open the door. – Switch off ON/OFF switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, ...