Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Turn the water off at the tap. When disposing of old appliances Appliances that have reached the end of their service life should be rendered inoperable in order to exclude the possibility of subsequent accidents. Pull the mains plug out of the wall socket, cut through the connecting cable and disable the door lock. Take the appliance to a designated waste disposal centre. Warning Children could get locked in the appliance (risk of suffocation) or get stuck in other positions. Therefore: Remove the mains plug, cut the mains wire and set aside. Damage the door lock so that the door can no longer be closed. en Getting to know your appliance Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front. Individual positions are referred to in the text. Control panel 1 Main switch 2 Door handle 3 Button for UPPER RACK washing function * 4 PROGRAMME END indicator 5 LOW SALT indicator 6 LOW RINSE-AID indicator 7 “Check water supply” indicator 8 Programme buttons * on applicable models Appliance interior 20 Upper basket with 2-tiered cup rack 21 Additional cutlery basket for the top basket * 22 Upper spray arm 23 Lower spray arm 24 Container for special salt with level indicator * 25 Filters 26 Cutlery basket 27 Lower basket 28 Lock for detergent dispenser 29 Container for rinse-aid, with level indicator 30 Detergent compartment 31 Nameplate * not on all models You will need to purchase the following before using the dishwasher for the first time: – special salt for use in dishwashers – detergent – rinse-aid Only use products, which are suitable for dishwashers. en Water softener In order to rinse dishes and glasses satisfactorily, the dishwasher requires soft water, i.e. containing little or no lime, otherwise water stains will be left behind on crockery and glasses, etc. If the tap water exceeds a certain level of hardness, it must be softened, i.e. decalcified, so that it can be used in the dishwasher. This is achieved by adding a special salt to the water softener inside the dishwasher. The water softener, that is the required amount of salt, is set up according to how hard the tap water is. Setting up the water softener Determine the level of hardness of your tap water. Your local water company or service agent can help you with this. Identify setting from the following water hardness table. Hold down the programme button B and switch on the main switch 1 , then release the buttons. The display 5 flashes and buttons A and B illuminate. (Hardness value 2 was set at the factory). Water hardness table To change the setting: Press programme button B . Each depression of the button increases the set value by one (0–3). If buttons A , B and C illuminate, the maximum hardness value has been reached. If the hardness value is now increased again, the illuminated buttons go out and the hardness value is set to 0 (no buttons illuminated). Switch off the mains switch 1 . The set value is stored in the appliance. Approx. 4 litres of water are required for regenerating the water softening system. The overall water consumption per load can therefore be increased by between 0 and a maximum of 4 litres according to the water hardness setting. dh fH Clarke mmol/ l A B Reset C 0–6 0–11 0–8 0–1,1 0 7–16 12–29 9–20 1,2–2,9 1 17–21 30–37 21–26 3,0–3,7 2 22–35 38–60 27–44 3,8–6,2 3 en Filling the special salt container How the salt works While washing is taking place, salt is automatically rinsed out of the salt container into the water softener where it dissolves the lime in the water. The dissolved lime is pumped out of the dishwasher. The water softening system is then ready for the next load. This process of regeneration can only function when the salt is dissolved in water. Unscrew the lid on the salt container 24 . Before you use the dishwasher for the first time, pour approx. 1 litre of water into the salt container. Use the enclosed salt filler. Refill with salt (do not use edible salt) until the salt dispenser is full (max. 1.5 kg). When the salt dispenser is being refilled, water is displaced and drains away. Therefore always refill the salt dispenser immediately before switching on the dishwasher (to prevent corrosion). As a result, the overflowing salt solution will be immediately diluted and rinsed out. Then remove salt residue from the filler area and screw on the dispenser cover, ensuring that it is not fitted askew. * not included with all models The LOW SALT indicator 5 on the front panel will light up initially but will extinguish again after a short period when the salt solution has become sufficiently concentrated. If the switch is set to ”0”, it is not necessary to add any salt, as none is consumed while the dishwasher is operating. If the switch is set between ”1” and ”3”, then salt must be added. Do not pour detergent into the container for special salt. This would destroy the water softener. LOW SALT indicator Salt should be added as soon as the LOW SALT indicator ...
Este manual também é adequado para os modelos :Máquinas de lavar louça - SRV43A23/28 (1.89 mb)
Máquinas de lavar louça - SRV43A23/30 (1.89 mb)
Máquinas de lavar louça - SRV43A23/31 (1.89 mb)