Assessments - , GPA:
(
)
)
Fabricante : Bosch
Arquivo Tamanho: 1.88 mb
Arquivo Nome :
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
por este dispositivo também tem outras instruções :
Facilidade de uso
Screw water connection on again. Check for leaks. Reconnect power supply. Switch on the appliance. Cold water connection (blue) not Connect cold water connection (blue). connected. Hot water connection (red) not Connect hot water connection (red) connected and additional “Hot or deselect additional function “Hot water”. water” function selected. Error code “:.. is lit. Filters 1R are soiled Clean filters. or blocked. (See Cleaning and maintenance) Error code “:.… is lit. Waste water hose Install hose without kinks, remove any is blocked or kinked. residue. Siphon connection still sealed. Check connection to siphon and open if required. Cover on the waste water pump Lock cover correctly. loose. (See Waste water pump) Error code “:.† is lit. Waste water pump blocked Clean pump and lock cover correctly. (See or cover on the waste water Waste water pump) pump is not locked in position. Error code “:.. is lit. Mains voltage too low. Not an appliance fault, have the mains voltage and electrical installation checked. en Fault, what to do? Fault Cause Remedial action A different error code is indicated on the digital display. A technical fault has probably occurred. Switch off appliances with the ON/OFF switch (. After a short time restart the appliance. (“:‹‚ to “:„‹) If the problem recurs, turn off the tap and pull out the mains plug. Call customer service and mention the error code. Display flashes Door not closed properly. Close the door. Ensure that no objects (utensil, fragrance dispenser) are protruding over the basket and preventing the door from closing. Refill indicator for salt @ and/or rinse-aid H is lit. No rinse aid. No salt. Refill rinse aid. Refill with special salt. Sensor does not detect salt tablets. Use different special salt. Refill indicator for salt @ and/or rinse-aid H is not lit. Refill indicator switched off. There is still enough special salt/ rinse aid available. Activation/deactivation (see chapter Water softening system/Special salt or Rinse aid). Check refill indicator, levels. Water is left in the appliance at the end of the programme. Filter system or area under the filters 1R is blocked. The programme has not yet ended. Clean filters and area underneath (see Waste water pump). Wait until programme ends or reset (see Terminating the programme). Fault, what to do? en Fault Cause Remedial action Utensils not dry. No or too little rinse aid in the dispenser. Programme selected without drying. Water collecting in depressions on the utensils and cutlery. The combined detergent used has a poor drying performance. Refill rinse aid. Select programme with drying (see Overview of programmes, Programme sequence). Arrange utensils in a sloping position, arrange affected utensils as sloping as possible. Use different combination detergent with better drying performance. Use of rinse aid also increases the drying performance. Intensive drying to increase drying not activated. Utensils were removed too early or drying process had not ended yet. The eco rinse aid used has a poor drying performance. Water supply connection interchanged. Activate intensive drying (see Operating the appliance) Wait until program ends or wait until 30 min after program ends before removing utensils. Use a proprietary rinse aid. Eco products are much less effective. Connect correctly water supply hose (see Fresh water connection). Plastic utensils not dry. Special properties of plastic. Plastic has a lower heat storage capacity and therefore dries less well. Cutlery not dry. Cutlery not arranged properly in the cutlery basket. Cutlery not arranged properly in the cutlery drawer. Separate cutlery if possible, prevent contact points. Arrange cutlery properly and separate if possible. Appliance interior wet after rinse cycle. No appliance fault. On account of the “Condensation drying” principle, water droplets are physically induced and required in the container. The humidity in the air condenses on the inner walls of the dishwasher, drains and is pumped out. en Fault, what to do? Fault Cause Remedial action Food remnants Utensils placed too closely Arrange utensils with adequate clearance on the utensils. together, utensils basket between them ensuring that the spray jets overfilled. can reach the surface of the utensils. Prevent contact points. Spray arm rotation obstructed. Arrange utensils so that the spray arm can rotate without obstruction. Spray arm nozzles blocked. Clean the spray arm nozzles, (See Cleaning and maintenance). Filters 1R dirty. Clean filters, (see Cleaning and maintenance). Filters 1R inserted incorrectly Insert and engage filters correctly. and/or not engaged. Rinse programme too weak. Select a more intensive rinse programme. Utensils precleaned too intensely; Do not prerinse utensils. Remove only large sensors therefore decide on food remnants. weak programme sequence. Stubborn soiling cannot be Recommended programme Eco 50° or Intensive. completely removed. Tall narrow receptacles in corner Do not...
Este manual também é adequado para os modelos :Máquinas de lavar louça - S51M63X6EU/73 (1.88 mb)