Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Problem Possible fault Solution The program does not start. The door is not properly closed. Close the door firmly. The machine is not plugged in. Insert the plug. The fuse is defective or the breaker has tripped. Reset the circuit breaker. See data plate for minimum amperage. The dishwasher is not turned on. Turn the dishwasher on "" and select a program. The dishwasher stops during a program. The fuse has tripped. Reset the circuit breaker. See data plate for minimum amperage. The buzzer sounds. All program indicators are flashing fast when the door is open. There may be a technical fault. Turn the dishwasher off "". After a few seconds: – Turn the dishwasher on. – Select the desired program with the program button. – Close the door. If the problem persists contact Technical Service. The drain pump is running when the door is opened. The waterproof system has activated. – Turn off the water supply. – Contact Miele Technical Service. Frequently asked questions Problems with water Intake / Drain Problem Possible fault Solution Shortly after the program start the dishwasher stops running. The buzzer sounds. The Intake / Drain indicator flashes when the door is open. The water supply is shut off. – Open the water supply. The dishwasher stops. The buzzer sounds. Before fixing the fault: – Turn the dishwasher off "". Fault in the water – Open the water supply all the way. The "Intake / Drain" indicator flashes when the door is open. intake. – Clean the water intake filter, see "User Maintenance Instructions". – The water pressure at the water connection is lower than 4.35 psi. Consult a plumber. Fault in the water – Clean the triple filter. drain. – Clean the drain pump and the There may be non-return valve. water in the wash See "User Maintenance Instructions" cabinet. for more info on the above. – Remove any kinks in the drain hose. Frequently asked questions General problems with the dishwasher Issue Possible fault Solution The display turns off. The dishwasher has gone into "Standby" mode to save energy. Press any button. The display turns on again. Detergent is left in the dispenser at the end of a program. The dispenser was damp when detergent was added. Dry the dispenser before adding detergent. The detergent lid cannot be closed properly. Detergent residue is blocking the catch. Remove the residue. The door and the interior walls are still wet after a program has finished. This is not a fault! It is the normal operating mode of the drying system. The moisture will evaporate after a short time. Water remains in the wash cabinet at the end of a program. Before fixing the fault: – Turn the dishwasher off "". The triple filter in the wash cabinet is clogged. Clean the triple filter. See "User Maintenance Instructions". The drain pump or the non-return valve may be blocked. Clean the drain pump and the non-return valve, see maintenance instructions. The drain hose is kinked. Remove any kinks from the drain hose. Frequently asked questions Sounds Problem Possible fault Solution There is a knocking noise in the wash cabinet. The spray arm is hitting an item in the basket. Interrupt the program, rearrange items blocking the spray arms. There is a rattling noise in the wash cabinet. Items are not secure in the wash cabinet. Interrupt the program and rearrange loose pieces. There is a knocking noise in the water pipes. This may be caused by the installation or the diameter of the pipe. This has no effect on the dishwasher. If in doubt contact a plumber. Frequently asked questions Poor cleaning results Problem Possible fault Solution The dishes are not clean. The dishes were not loaded correctly. See "Loading the dishwasher". The program was not powerful enough. Select a more intensive program, see "Program Guide". Not enough detergent was dispensed. Use more detergent, see "Adding detergent". The spray arms are blocked by items. Turn the spray arm and rearrange the dishes if necessary. The triple filter in the base of the wash cabinet is not clean or not correctly inserted. The spray arm jets might be clogged. Clean the filter and insert it correctly. Clean the spray arm jets. See "User Maintenance Instructions". The drain pump or the non-return valve is blocked. Wash water will run back into the wash cabinet. Clean the drain pump and the non-return valve, see maintenance instructions. Glasses and cutlery show streaks. There is a bluish sheen on the surface of glasses and a film that can be wiped off. The rinse aid dosage is set too high. Reduce the dosage, see "Before using for the first time". Frequently asked questions Problem Possible fault Solution Dishes are still wet, glasses and cutlery are spotted. The rinse aid setting may be too low, or the rinse aid reservoir is empty. Dishes were taken out to...