Assessments - 3, GPA: 5
(
)
)
|
Facilidade de uso
. Load Button This function allows the dishwasher to wash dishes using only the upper rack if there are not enough dishes for a full load. This will allow you to save on water and energy consumption. To select . load: 1. Select the programme and then press the . load button (Fig.2-17) – the . load indicator blinks. 2. Close the door. The programme starts automatically. To cancel the . load 1. Open the door slightly. 2. Press the programme button and hold it in for about 3 seconds. Please keep in mind that the amount of detergent should also be adapted to the . load. 6h 4h 2h 6h 4h 2h 6h 4h 2h 6h 4h 2h 6h 4h 2h 6h 4h 2h 6h 4h 2h ........................................................................................ Fig.2-15 Fig.2-16 1 2 Fig.2-17 9 Memory Function Module If a power cut occurs while the selected washing program is active, the program is not cancelled. The controls use a microprocessor device to memorize the information about the selected washing program. Once the power is returned to the machine, the dishwasher will resume from the point it was interrupted. Cancelling or modifying a washing program cycle 1. To modify or cancel a washing cycle it is necessary to reset the previous programming, by holding the programme button for at least 3 seconds. The buzzer will emit one short warning signal. 2. If the reset operation was successful, a drain phase will start. Once the drain phase has ended a new programme can be selected. 3. Looking after your Dishwasher Care After Every Wash After every wash, set the ON-OFF button to OFF and leave the door slightly ajar so that moisture and odours are not trapped inside. Before cleaning or performing maintenance isolate . from mains. Overall condition of appliance Check that no grease or scale has accumulated on the inside of the dishwasher. If you discover any deposits: Clean the interior of the dishwasher thoroughly with a detergent solution. Dishwasher salt Check the LOW SALT indicator. Top up with salt, if required (Fig.3-1). Filters The filters prevent larger particles of food in the water from reaching the pump. These particles may occasionally block the filters. When the appliance has finished washing, check the filters for particles of food and, if required, clean. After undoing the coarse micro-filter (Fig.3-2), the filter unit can be removed (Fig.3-3). Remove any particles of food and rinse the filters under running water. Insert the filter unit and tighten the coarse micro-filter. Fig.3-1 Fig.3-2 Fig.3-3 11 Spray arms Limescale and remnants of food in the washing water can block the nozzles in the spray arms and the arm mountings. Inspect the nozzles in the spray arms for blocked holes due to remnants of food. If necessary, pull the lower arm (Fig.3-4) upwards and lift it off. Unscrew the upper spray arm (Fig.3-5). Clean both spray arms under running water. .Refit the spray arms. Ensure that the lower arm has locked into place and the upper one is screwed tight. position. If absolutely necessary, it can be positioned on its back. Seals One of the factors that cause odours to form in the dishwasher is food that remains trapped in the seals. Periodic cleaning with a damp sponge will prevent this from occurring. When You Go on Holiday When you go on holiday, it is recommended that you Fig.3-4 Fig.3-5 position. If absolutely necessary, it can be positioned on its back. Seals One of the factors that cause odours to form in the dishwasher is food that remains trapped in the seals. Periodic cleaning with a damp sponge will prevent this from occurring. When You Go on Holiday When you go on holiday, it is recommended that you Fig.3-4 Fig.3-5 run a wash cycle with the dishwasher empty and isolate from the mains. Turn off the water supply and leave the door of the appliance slightly ajar. This will help the seals last longer and prevent odours from forming within the appliance. 12 4. Troubleshooting Resolving minor problems yourself Experience has shown that you can resolve most problems that occur during normal daily usage yourself, without having to call out a service engineer. Not only does this save costs but it also means that the appliance is available to use. The following list of common occurrences and their remedies should help you identify the causes of most problems. Problems when the unit is switched on Appliance does not start up • Fault with fuse in mains electricity supply. • Plug not inserted in wall socket. • Appliance door not closed properly. • Programme button has not been pressed. Water tap not turned on. • Blocked strainer in water intake hose. Caution: Remember that repairs should only . be carried out by a suitably qualified specialist. Improper repairs can lead to considerable equipment damage as well as danger to the user. Problems with the appliance Error display on the programme indicator • When the programme indicators A1 and A2 blink (Fig.4-1). Have you checked if the door is closed properly? • When the programme indicators A1,...
Este manual também é adequado para os modelos :Máquinas de lavar louça - RDW945FI (713.12 kb)