Log:
Assessments - 0, GPA: 0 ( )

Instruções de Operação Samsung, Modelo Waterwall Dishwasher DW80H9950U

Fabricante : Samsung
Arquivo Tamanho: 5.02 mb
Arquivo Nome :
Língua de Ensino: enesfr
Ir para baixar



Facilidade de uso


installing the dishwasher
Plumbing
1. Check the hot water connection on the front left-side of the base of the dishwasher.
The mounting plate should be secured to the front of the base, the threads inside the
connection should be smooth and shiny, and the area should be clean and free of any
debris.
2. Make sure the dish washer and the accessories are all included in the package to ensure
these assemblies are not cracked and that all connections are secure.
3. Check the drain hose for any holes or deformities that could allow a water leak during
draining.
Electrical
1. Confi rm the junction box cover is secured to the junction box on the front right-side of the
base of the dishwasher.
2. Confi rm the electrical box was not damaged during shipping and that it is secured to the
base of the dishwasher.
Appearance
1. Confi rm there are no dents or scratches on the front of the dishwasher.
2. Check the edges of the doors for any roughness or cracking
3. Check the control panel to ensure it is clear and unscratched, and that all the control markers
are in their proper places.
Parts
1. Confi rm you have all the parts listed in Step 1 on page 6.
STEP 6 PREPARING THE DISHWASHER
1. Ensure that the circuit breaker and water supply valve are turned off before proceeding with
the following steps.
Before you move or lay down the dishwasher for installation, make sure to adjust the height
CAUTION of the legs so the legs are as short as possible. This prevents the legs from breaking.
Level the dishwasher by adjusting the height of the legs after you have the dishwasher in
place.
2. Wrap Tefl on tape on both sides of the 90 ˚ elbow. Then, insert the elbow into the inlet
valve (see Figure 4-B). Tighten until the elbow is tight and pointing towards the water hose
channel in the base of the dishwasher (about 4 o'clock). To prevent the inlet valve from being
blocked, make sure that the Tefl on tape does not enter the valve. Do not over tighten.
3. Cut the strings securing the drain hose to the back of the dishwasher. Roll-out the hose.
Make sure there are no kinks and that the hose is not bent at any extreme angles that could
constrict the fl ow of water.
4. Remove the junction box cover located at the bottom front right of the dishwasher using a
screwdriver, and then Install the strain relief (Figure 4 - C). Make sure to keep the junction box
cover you removed. It is used in Step 10, Wiring Connections.
5. If the countertop is made of wood or a material that is not damaged by drilling, attach the
two (2) Installation brackets that were supplied with the dishwasher using the supplied
screws (Figure 4 - A). They will be used in Step 8, Securing the Dishwasher.
6. Use the provided clamp to connect the provided drain hose to the outlet at the back of the
product. If the product has the drain outlet in the right side, use the provided holder hose to
facilitate the connection.
12_ installing the dishwasher
DW80H9950US-00151A-06_EN_150216.indd Sec3:12
DW80H9950US-00151A-06_EN_150216.indd Sec3:12
2015-02-16
2015-02-16 9:57:07
9:57:07


...

Este manual também é adequado para os modelos :
Máquinas de lavar louça - Waterwall Dishwasher DW80H9970U (5.02 mb)
Máquinas de lavar louça - Rotary Dishwasher DW80H9940U (5.02 mb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias