Assessments - , GPA: ( )

Instruções de Operação Bosch, Modelo 685000800012

Fabricante : Bosch
Arquivo Tamanho: 427.04 kb
Arquivo Nome : 685000800012.pdf

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

NOTE: Install Top Mount Clips before unit is installed into the cabinet. Insert the installation brackets to the front top slots of the dishwasher. (See image below) To install the Side Mounting Clips. Depending on space allowed in cabinet the Side Mounting Clips can be installed with the holes for the screw up (preferred method) or down as shown in the illustrations below. NOTE: Install Side Mount Brackets before unit is installed into the cabinet. Insert the installation brackets to the side slots of the dishwasher. (See image below) Figure 1a Cut Hazard To prevent serious injury from sharp edges, wear work gloves when handling, unpacking or disassembling unit. 685000800012 09/10 Figure 1b 3. Remove two (2) screws at front of the kickplate brace using a #2 Phillips screw driver. Slide up and pull off. Figure 4 WATER LINE (NOT INCLUDED) ELECTRICAL BOX 34” Min to 35” Max.** 90 90 18” 3” 3” Preferred Drain Areas 13/4” 13/4” 13/4” 13/4” 24” **Note: 35” max. Height for standard cabinetry cutout. (5/16” min. Clearance required from unit to 31/ underside of countertop.) 2” min. to 41/2” max. 24” 3” Figure 3 *DIMENSIONSDONOT INCLUDE INSULATION 1. Measure height of cabinet opening from underside of countertop to floor. 2. Move dishwasher to front of installation area. 3. Loosen the rear leveling legs by turning counterclockwise. 9. Check that dishwasher is level from side to side by placing a level against the top front section of the tub. See Figure 5a. 6. If levelers need to be removed, make sure that the floor is free of all obstructions. 7. Carefully place dishwasher inside cabinet area such that is centered in opening. Use caution when moving dishwasher to prevent damage to cabinet, dishwasher and floor. 8. Front of door needs to be even with the front of adjoining cabinets. Front levelers should allow 5/16” below underside of countertop to top of console. Figure 5a Figure 5b 10. Check that the dishwasher is level from front to back by taking out the lower rack, place level on the lower rack wheel support at the bottom of the tub. See Figure 5b. 11. Adjust levelers up or down until dishwasher is level. Holes need to be pre-drilled using a #5 drill to secure unit. 12. Screw mounting brackets firmly to cabinet using screws provided in literature packet. See Image Below. Figure 5c Figure 5d 13. Open the door remove the tub cap on both sides of the tub. Install screw through the dishwasher side hole to the wall of cabinet. Reinstall tub cap. 14. Open and close dishwasher door slowly. Ensure that there is clearance to the console. Adjust accordingly until door opens and closes freely. 233/4” 333/4” 273/8” 503/8” 25 23” 1/2” Cut Hazard Electric Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Failure to follow this warning could result in death or serious injury. Metal color panels are sharp and should be handled with care. Wear gloves to protect hands. Failure to follow this warning may result in injury. Checking the Installation 8 Operate the machine through at least one fill and pump-out, checking the following items: . At first fill, approximately 1 minute make sure water completely covers filter surface. ....