Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
If you are not sure about the insulation in your mobile home, or if you notice that the outer walls and ceiling are either hot or cold, install the alarm on an inside wall. For minimum protection, install at least one alarm close to the bedrooms. For additional protection, see SINGLE FLOOR PLAN in Diagram B. WARNING: TEST YOUR SMOKE ALARM OPERATION AFTER R.V. OR MOBILE HOME VEHICLE HAS BEEN IN STORAGE, BEFORE EACH TRIP AND AT LEAST ONCE A WEEK DURING USE. . Smoke Alarms for Minimum Protection .. Smoke Alarms for Additional Protection ^^ Ionization Type Smoke Alarms with 2. LOCATIONS TO AVOID •In the garage. Products of combustion are present when you start your automobile. • Less than 4” (10cm) from the peak of an “A” frame type ceiling. •In an area where the temperature may fall below 40.F or rise above 100.F. •In dusty areas. Dust particles may cause nuisance alarm or failure to alarm. •In very humid areas. Moisture or steam can cause nuisance alarms. •In insect-infested areas. •Smoke alarms should not be installed within 3 ft (.9m) of the following: the door to a kitchen, the door to a bathroom containing a tub or shower, forced air ducts used for heating or cooling, ceiling or whole house ventilating fans, or other high air flow areas. •Kitchens. Normal cooking may cause nuisance alarms. If a kitchen alarm is desired, it should have an alarm silence feature or be a photoelectric type. • Near fluorescent lights. Electronic “noise” may cause nuisance alarms. 3. INSTALLATION INSTRUCTIONS CAUTION: THIS UNIT IS SEALED. THE COVER IS NOT REMOVABLE! When wall mounting, When mounting the “A” line should in a hallway, the be horizontal and “A” line should the “UP FOR WALL be parallel with MOUNTING” arrow the hallway. must be pointing up. FIGURE 1 FIGURE 2 Alignment Marks Install Remove FIGURE 3 FIGURE 4 1. Remove the mounting plate from the back of the alarm by holding the mounting plate and twisting the alarm in the direction indicated by the “OFF” arrow on the alarm cover. 2. To insure aesthetic alignment of the alarm with the hallway or wall, the “A” line on the mounting plate must be parallel with the hallway when ceiling mounting or horizontal when wall mounting. 3. After selecting the proper smoke alarm location as described in Section 1, attach the mounting plate to the ceiling as shown in Figure 1. For wall mounting see Figure 2. Place mounting plate on the wall. Be sure the “UP FOR WALL MOUNTING “ text and arrow are facing up. Use the screws and anchors provided to secure the mounting plate (use 3/16” drill bit for anchors). 4. Battery installation instructions are provided on the inside of the battery door for Safety Light and Smoke Alarm use. To ensure proper installation of the Safety Light and Smoke Alarm battery follow the instructions. CAUTION! MAKE SURE TO INSTALL THE PROPER LONG LIFE BATTERY (SEE SECTION 6) IN THE COMPARTMENT THAT POWERS THE SMOKE ALARM AND THE ALKALINE BATTERY IN THE COMPARTMENT THAT POWERS THE SAFETY LIGHT. REVERSING THESE WILL ELIMINATE THIS SMOKE ALARM’S LONGLIFE BATTERY CAPABILITY AND MAY DAMAGE THE SAFETY LIGHT. 5. When installing the battery, press the battery reminder finger down into the battery compartment and install the battery (see Figure 3). CAUTION! IF THE BATTERY REMINDER FINGERS ARE NOT HELD DOWN IN THE BATTERY COMPARTMENT BY THE BATTERIES, THE BATTERY DOOR WILL NOT CLOSE, AND THE UNIT WILL NOT ATTACH TO THE MOUNTING BRACKET. 6. Alignment marks are provided on the edge of the trim plate and the alarm. After installing the mounting plate, place the alarm on the mounting plate with the alignment marks lined up. Twist the alarm in the direction indicated by the “ON” arrow on the alarm cover (see Figure 4) until it locks in place. 7. USING TAMPER RESIST LOCKING PIN: To make your smoke alarm somewhat tamper resistant, a locking pin has been provided in the bag with the screws and anchors. Using this pin will deter children and others from removing the alarm from the mounting plate. To use the pin, insert it into the hole in the side of the alarm after the alarm has been installed on the mounting plate (see Figure 5). FIGURE 5 Tamper ResistLocking Pin NOTE: THE TAMPER RESIST PIN WILL HAVE TO BE REMOVED IN ORDER TO CHANGE THE BATTERIES. USE A LONG NOSE PLIERS TO PULL THE PIN OUT OF THE HOLE. IT IS NOW POSSIBLE TO REMOVE THE ALARM FROM THE MOUNTING PLATE. 8. After installation, test your alarm by depressing and holding down the test button for several seconds. This should sound the alarm. 4. OPERATION AND TESTING OPERATION: The smoke alarm is operating once a fresh battery is installed and testing is complete. When products of combustion are sensed, the unit sounds a loud 85db pulsating alarm until the air is cleared. SAFETY LIGHT: The model 0918K has a Safety Light feature. When the smoke alarm ionization chamber senses smoke, the 85db horn will sound and the Safety Light will flash until the sensing chamber is cleared of smoke particles. NOTE: THE SAFETY LIGHT IS NOT I...
Este manual também é adequado para os modelos :Alarme de incêndio - 0918K (152.76 kb)