Fabricante : First Alert
Arquivo Tamanho: 435.02 kb
Arquivo Nome : d6ce7340-3cbd-425d-bbe2-950579ae253d.pdf
![en en](/images/flag/s/en.gif)
![]() |
Facilidade de uso
If CO presence still indicates a potentially dangerous situation, the horn will sound again. IF THE CO LEVELS RETURN TO NORMAL: HORN: Silent DISPLAY: Dash lit by “READY” POWER/ALARM LIGHT: Shines continuously USING THE PEAK CO MEMORY The CO Memory Feature lets you check the highest level of CO recorded during an alarm. To check CO Memory: 1. Press and release the Test/Silence/Scroll button until the dash scrolls to “MEMORY”. 2. Press and hold Test/Silence/Scroll button to display Memory CO level. To clear CO Memory: 1. Press and release the Test/Silence/Scroll button until the dash scrolls to “CLEAR MEMORY.” 2. Press and hold the Test/Silence/Scroll button until the display shows “CLr.” NOTE: The highest CO level will be saved, even after a power interruption, until you clear it. DO NOT clear the CO Memory reading if you plan to call someone to investigate a CO problem! Clear the CO Memory reading only after the investigator has checked your home. WHERE CO ALARMS SHOULD NOT BE INSTALLED DO NOT locate this CO Alarm: • In garages, kitchens, furnace rooms, or in any extremely dusty, dirty or greasy areas. • Closer than 15 feet (4.6 meters) from a furnace or other fuel burning heat source, or fuel burning appliances like a water heater. • Within 5 feet (1.5 meters) of any cooking appliance. • In extremely humid areas. This Alarm should be at least 10 feet (3 meters) from a bath or shower, sauna, humidifier, vaporizer, dishwasher, laundry room, utility room or other source of high humidity. • In areas where temperature is colder than 40°F (4°C) or hotter than 100°F (38°C). These areas include non-airconditioned crawl spaces, unfinished attics, uninsulated or poorly insulated ceilings, porches, and garages. • In turbulent air, like near ceiling fans, heat vents, air conditioners, fresh air returns, or open windows. Blowing air may prevent CO from reaching the sensors. • In direct sunlight. • In outlets covered by curtains or other obstruction. • This CO Alarm is designed for use inside a single-family home or apartment. It is not meant to be used in common lobbies, hallways, or basements of multi-family buildings unless working CO Alarms are also installed in each family living unit. CO Alarms in common areas may not be heard from inside individual family living units. • This CO Alarm alone is not a suitable substitute for complete detection systems in places which house many people, like hotels or dormitories, unless a CO Alarm is also placed in each unit. • DO NOT use this CO Alarm in warehouses, industrial or commercial buildings, special-purpose non-residential buildings, RVs, boats, or airplanes. This CO Alarm is specifically designed for residential use, and may not provide adequate protection in non-residential applications. WHEN THE ELECTRICITY COMES IF THE CO ALARM IS NOT BACK ON: OPERATING PROPERLY: HORN: May chirp briefly HORN: Three rapid chirps every minute DISPLAY: Dash appears by “READY” DISPLAY: Displays “Err” POWER/ALARM LIGHT: Shines POWER/ALARM LIGHT: Flashes continuously. three times in sync with the horn. What you see and hear if CO is detected: PRE-ALARM LEVELS: IF YOU SILENCE THE ALARM: PLUG THE ALARM INTO AN OUTLET This CO Alarm should receive continuous electrical power. Do not plug this Alarm into an outlet controlled by a dimmer or switch. 1. Plug the unit into a standard UNSWITCHED 120V AC outlet. The unit should be located where it can wake you if it alarms at night. 2. Make sure the POWER/ALARM light shines continuously when you plug it in. The horn may “chirp” during power up, or when power is restored after an outage. 3. Test by pressing the Test/Silence/Scroll button firmly until the unit sounds: 4 beeps, pause, 4 beeps. During testing, the POWER/ALARM light will flash and “888” will appear briefly on the Display. This is normal. PREPARE YOUR ALARM LABELS Find the pair of self-adhesive labels included with this CO Alarm. • On each label write in the phone number of your emergency responder (like 911) and a qualified appliance technician. • Place one label near the CO Alarm, and the other label in the “fresh air” location you plan to go if the alarm sounds. NOTE: A qualified appliance technician is defined as “a person, firm, corporation, or company that either in person or through a representative, is engaged in and responsible for the installation, testing, servicing, or replacement of heating, ventilation, air conditioning (HVAC) equipment, combustion appliances and equipment, and/or gas fireplaces or other decorative combustion equipment.” HOW TO INSTALL YOUR CO ALARM IMPORTANT! Read all instructions before using this product. Quick reference: • Plug the Alarm into a standard 120V unswitched outlet. • Test the CO Alarm. USING THE SILENCE FEATURE The Silence Feature is intended to temporarily silence your CO Alarm’s horn while you correct the problem—it will not correct a CO problem. While the alarm is silenced, it will continue to monitor the air for CO. To Activate the Silence...