Assessments - 5, GPA: 3.4
(
)
)
|
Facilidade de uso
The default address is "0" (all DIP switches set to "off"). The DIP switch settings for all approved addresses are listed on pages 5-6 (0 = off, 1=on). Address (A) Operating mode Network structure Loop Stub T-tap 0 Automatic address assignment in "improved version" LSN mode X X - 1 to 254 Manual address assignment in "improved version" LSN mode X X X 255 = CL Automatic address assignment in "classic" LSN mode (address range: max. 127) X X - x = possible - = not possible i NOTICE! It is not permitted to use different operating modes in one loop/stub/T-tap next to each other. Installing the Unit ! WARNING! The equipment may only be installed by authorized and qualified personnel! Switch off the unit before carrying out any connection work! Bosch Sicherheitssysteme GmbH F.01U.088.879 | 3.0 | 2009.07 28 en FAS-420-TM | FAS-420-TM-R | FAS-420-TM-RVB NOTICE! -When selecting the installation location, it must be ensured that the unit displays are easily visible. -Remember when planning that the unit fans generate a noise level of approx. 40 dB(A). -The air outlet on the unit must not be obstructed. The distance between the air outlet and adjacent objects, e.g. a wall, has to be at least 10 cm. -The aspirating smoke detector can be installed with the suction device upwards or downwards (to do this, the detection unit cover must be rotated through 180°). If the aspiration pipe points downwards, make sure no impurities enter the air-return pipe which then points upwards. i 1. First, clearly mark the fixing points on the installation position provided on the equipment. To guarantee a safe and low-vibration hold, the housing base must be secured with four screws (. max. 4 mm). 2. Fix the housing base to the surface by means of four screws in accordance with the mounting type. Make sure that the housing base is not fixed under mechanical tension and that the screws are not tightened too much. Otherwise, the device might be damaged or undesirable secondary noise may arise. 3. Using a screwdriver, carefully punch out the required cable entries from the housing base. 4. Carefully fit the cable entry/entries as required with M20 or M25 glands (1 x M25 and 2 x M20 included in the delivery) by inserting them into the corresponding cable entry/ entries. 5. Punch out the cable entries using a sharp object. Caution: Do not cut the cable entries with a knife! 6. Feed the connection cable(s) (max. cable cross section 2.5 mm.) through the suitable cable entry/entries into the device and cut to the required length inside the device. 7. Wire the unit according to the connection information described below. Connecting the FAS-420-TM Series i NOTICE! The units are usually connected to an additional power supply. When connecting to a Bosch fire panel LSN improved version, the voltage is supplied via the AUX outputs of the battery charger module. Alternatively, an external mains unit (e.g. FPP-5000 or UEV 1000) can be used. Figure 4, Page 4 Designation Cable Function V+ Red Additional power supply, incoming V-Black V+ Red Additional power supply, outgoing V-Black a1White LSN a, incoming b1+ Yellow LSN b, incoming a2White LSN a, outgoing b2+ Yellow LSN b, outgoing Shield -Shield wire Data+ -Data line connection for digital external detector alarm display* Data- *Digital external detector alarm displays for the FAS-420-TM Series must be ordered separately. F.01U.088.879 | 3.0 | 2009.07 Bosch Sicherheitssysteme GmbH FAS-420-TM | FAS-420-TM-R | FAS-420-TM-RVB en 29 LSN Configuration Once the aspirating smoke detector has been connected to the LSN, the detector and detector unit are configured using the fire panel programming software via a laptop con...
Este manual também é adequado para os modelos :Alarme de incêndio - FAS-420-TM-R (1.77 mb)
Alarme de incêndio - FAS-420-TM-RVB (1.77 mb)