Assessments - 5, GPA: 3.8
(
)
)
|
Facilidade de uso
VDRVDR5V 3.4 Precautions in Installing the Printer The printer must only be operated horizontally. Do not operate vertically or install on a wall. Horizontal position Vertical position CAUTION! DO NOT use the printer under the following conditions. ¦ A state subject to vibration or unstable state. ¦ A state with this product slanted. • Otherwise dropping may cause injury. • Poor print quality may occur. ¦ A state where this product is installed vertically or sidelong. • Malfunction, failure, or electric shock may result. — 14 — 3.5 Partition for Paper Roll 3.5 Partition for Paper Roll At the time of shipment, this partition is set to “80-mm 80 mm 58mm 60mm CAUTION! When setting the partition to the slot for 58 mm or 60 mm paper roll, be sure not to set it slanted. Partition wide roll paper position”. 1. Confirm that the power switch is OFF. 2. Open the printer cover. 3. Set the partition to each to the slot which meets the width of the paper roll used.When using the 83-mm wide paper roll, remove the partition. 4. Change the setting of paper width by reffering to the section 5.2, "Manual Setting of Memory Switch". 3.6 Setting DIP Switch DIP switch The DIP switch is present on the serial interface board. Interface board Remove the board fixing screws, take out the mounting screwsinterface board, and then set the DIP switch. The function of each switch is as shown below. CAUTION! When setting the DIP switch, DO NOT remove screws other than those for mounting the serial interface board. Switch No. Function ON OFF InitialSettings 1 Communication condition setting method DIP switch setting Memory switch setting OFF 2 Hand shake XON/XOFF DTR/DSR OFF 3 Bit length 7 bits 8 bits OFF 4 Parity check With parity None OFF 5 Parity selection Even parity Odd parity OFF 6 Baud rate selection See Table below. ON 7 ON 8 INIT Reset Invalid OFF Selecting baud rate Baud Rate (bps) Switch No. 6 7 2400 OFF OFF 4800 ON OFF 9600 OFF ON 19200 ON ON 1200, 38400, 57600 and 115200 bps can also be selected by a command, etc. — 15 — 3.7 Adjusting the Paper Near-end Sensor 3.7 Adjusting the Paper Near-end Sensor 1. Lightly push in the paper near-end sensor unit. 2. Move the paper near-end sensor unit to the right and left while keeping to press it.The sensor position is as shown below depending on the diameter of the roll paper used. Sensor Position Roll paper diameter at the detection of near-end Outer core diameter of roll paper used *1 .22 .18 2 .25 .22 3 .29 .25 4 .34 .32 * Factory setting CAUTION! ¦ Paper remaining differs by the type of paper roll used. ¦ The external diameter of the paper roll is only for reference. ¦ When a paper end error is detected incorrectly during using a paper roll with a honeycomb type core, move the sensor position to the larger number. 4321Paper-near-end sensor unit — 16 — 4. MAINTENANCE AND TROUBLESHOOTING 4.1 Setting/Replacing the paper roll 1. Lift the cover open button. 2. Open the printer cover. 3. Insert a paper roll with its print area facing down as shown in the figure and pull out the paper end straightforward by several cm out of the printer. 4. Firmly close the printer cover until a click can be heard. With the factory setting, the paper is fed and cut automatically. See 5.3 Manual Setting of Memory Switch CAUTION! ¦ Always use the specified types of paper roll. ¦ Confirm that the paper roll is set correctly. ¦ When the paper is skewed and not extended straightforward from under the printer cover, open the printer cover and adjust the paper correctly. ¦ When the cover is opened after paper setting, be sure to pull the paper straightforward by several cm out of the printer, and then close the cover. ¦ When closing the printer cover, press on the center part of the cover to close it firmly. ¦ When setting paper, be careful not to have your finger injured by the paper edge. WARNING When opening the printer cover, DO NOT touch the print head or cutter blade. Otherwise, burning or injury of hand may result. — 17 — 4.2 Removing Jammed Paper 4.2 Removing Jammed Paper 1. Turn the printer power off. 2. Open the printer cover. 3. Remove the jammed paper including any paper chips remaining. (Remove the paper roll set in the holder as well.) 4. Reinstall the paper roll and close the printer cover. 5. Turn on the printer. The auto cutter mechanism is initialized and the alarm is cleared. CAUTION! ¦ If the cutter blade remains protruded with paper jammed, press the FEED button. If the cutter blade does not move back, performe the above step 1 through 3 and then turn the printer on without a paper roll. Contact your Citizen Systems dealer. Be carefull not to have your hand injured by the cutter blade in the operation. ¦ The print head is hot immediately after printing. DO NOT touch it with your hand. DO NOT touch the heating element of the head with a bare hand or metal object either. 4.3 Cleaning the Print Head 1. Turn the printer power off. 2. Open the printer cover. 3. Wait several minutes. Wipe off any de...
Este manual também é adequado para os modelos :Impressoras - CT-S2000 (1.48 mb)
Impressoras - CT-S2000DCL (1.48 mb)
Impressoras - CT-S2000L (1.48 mb)