Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
A sample printout is shown in Figure 34 on page 81. NOTES on diagnostic printouts: • FE indicates a framing error. • OE indicates an overrun error. • PE indicates a parity error. • NE indicates noise. For any errors, check that your communication parameters are correct. Set the print width equal to or less than the label width used for the test. See page 46 for more information. Bradyprinter 200M-e and 200M-e 300 User’s Guide Selecting Prefix and Delimiter Characters Prefix and delimiter characters are 2-digit hex values used within the ZPL/ZPL II formats sent to the printer. The printer uses the last prefix and delimiter characters sent to it, whether from a ZPL II instruction or from the front panel. NOTE: DO NOT use the same hex value for the control, format, and delimiter character. The printer needs to see different characters to function properly. Press Display Shows Action/Explanation CONTROL PREFIX Control Prefix Character: Press the (–) key to move to the next digit position, press the (+) key to increase the value of the digit. Default: 7E (tilde -displayed as a black square) Range: 00 - FF The printer looks for this 2-digit hex character to indicate the start of a ZPL/ZPL II control instruction. FORMAT PREFIX Format Prefix Character: Press the (–) key to move to the next digit position, press the (+) key to increase the value of the digit. Default: 5E (caret) Range: 00 - FF The printer looks for this 2-digit hex character to indicate the start of a ZPL/ZPL II format instruction. DELIMITER CHAR Delimiter Character: Press the (–) key to move to the next digit position, press the (+) key to increase the value of the digit. Default: 2C (comma) Range: 00 - FF The delimiter character is a 2-digit hex value used as a parameter place marker in ZPL/ZPL II format instructions. For more details, contact Technical Support. Bradyprinter 200M-e and 200M-e 300 User’s Guide Selecting ZPL Mode Press Display Shows Action/Explanation ZPL MODE Selecting ZPL Mode: Press the (+) or (–) key to display other choices. Default: ZPL II Selections: ZPL II, ZPL The printer remains in the selected mode until it is changed by this front panel instruction or by using a ZPL/ZPL II command. The printer accepts label formats written in either ZPL or ZPL II. This eliminates the need to rewrite any ZPL formats you already have. For more details, contact Technical Support. Power-Up and Head Close Parameters MEDIA POWER UP Media Power-Up: Press the (+) or (–) key to display other choices. Default: Calibration Selections: Feed, calibration, length, and no motion This parameter establishes the action of the media when the printer is turned on. • Calibration: Recalibrates the media and ribbon sensors. • Feed: Feeds the label to the first web. • Length: Determines the length of the label. • No Motion: Media does not move. HEAD CLOSE Head Close: Press the (+) or (–) key to display other choices. Default: Calibration Selections: Feed, calibration, length, no motion Determines the action of the media after the printhead has been opened and then closed. • Calibration: Recalibrates the media and ribbon sensors. • Feed: Feeds the label to the first web. • Length: Determines the length of the label. • No Motion: Media does not move. Bradyprinter 200M-e and 200M-e 300 User’s Guide Label Positioning Parameters Press Display Shows Action/Explanation BACKFEED Backfeed Sequence: Press the (+) or (–) key to display other choices. Default: Default (90%) Selections: Default, after, before, 10%, 20%, 30%, 40%, 50%, 60%, 70%, 80%, off This parameter establishes when and how much label backfeed occurs after a label is removed or cut in the peel-off, cutter, and applicator modes. It has no effect in rewind or tear-off modes. This parameter setting can be superseded by the ~JS instruction when received as part of a label format (for more details, contact Technical Support). NOTE: The difference between the value entered and 100% establishes how much backfeed occurs before the next label is printed. For example, a value of 40 means that 40% of the backfeed takes place after the label is removed or cut. The remaining 60% takes place before the next label is printed. A value of “before” means that all backfeed takes place before the next label is printed. LABEL TOP Adjusting Label Top Position: Press the (+) key to increase the value, press the (–) key to decrease the value. The displayed value represents dots. Default: +0 Range: –120 to +120 dot rows The label top position adjusts the print position vertically on the label. Positive numbers adjust the label top position further down the label (away from the printhead), negative numbers adjust the position up the label (toward the printhead). LEFT POSITION Adjusting Left Position: Press the (–) key to move to the next position, press the (+) key to change between + and – and to increase the value of the digit. The displayed value represents dots. Default: 0000 Range: –9999 to +9999 NOTE: For a negative value, e...
Este manual também é adequado para os modelos :Impressoras - 200M-e (2.1 mb)