Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
Check the display screen for more information. CHECK RIBBON Off Normal operation — ribbon (if used) is properly loaded. On Printing is paused, the front panel displays a warning message, and the PAUSE light is on. • If the printer is in direct thermal mode: Ribbon is loaded. • If the printer is in thermal transfer mode: No ribbon is loaded. PAPER OUT Off Normal operation — media is properly loaded. On No media is under the media sensor. Printing is paused, the display shows an error message, and the PAUSE light is on. PAUSE Off Normal operation. On The printer has stopped all printing operations. Either the PAUSE key was pressed, a pause command was included in the label format, the on-line verifier detected an error, or a printer error was detected. Refer to the display screen for more information. DATA Off Normal operation. No data being received or processed. On Data processing or printing is taking place. No data is being received. Flashing The printer is receiving data from or sending status information to the host computer. Flashing slows when the printer cannot accept more data, but returns to normal once data is again being received. Brady X-PLUS Series User.s Guide Roll Media Loading NOTE: A calibration must be performed when media and ribbon (if used) are first installed in the printer, or when a different type of media or ribbon is being used. Tear-Off Mode Refer to Figure 16. 1. Open the printhead. 2. Slide the media guide and media supply guide as far from the printer frame as possible. Flip down the media supply guide. 3. Load media as shown. 4. Flip up the media supply guide. Slide in the media guide and media supply guide so they just touch, but not restrict, the edge of the roll. 5. Close the printhead. MediaguideMediaMediasupplyguideClosedOpenPrintheadlever Figure 16 Brady X-PLUS Series User.s Guide Peel-Off Mode NOTE: Rewind option required. Refer to Figure 17. 1. Remove the rewind plate from the front of the printer (if installed). Store it on the two mounting screws on the inside of the front panel. 2. Open the printhead. 3. Slide the media guide and media supply guide as far from the printer frame as possible. Flip down the media supply guide. 4. Load media as shown. 5. When loading media, allow approximately 36” (914 mm) of media to extend past the tear-off/peel-off bar. Remove all labels from this portion to create a leader. 6. Remove the hook from the rewind spindle. If you are using a core, slide it onto the rewind spindle until it is flush against the guide plate. 7. Wind the label backing around either the 3” (76 mm) core or the rewind spindle and reinstall the hook. 8. Flip up the media supply guide. Slide in the media guide and media supply guide so they just touch, but not restrict, the edge of the roll. Before closing the printhead, make sure: • The media is positioned against the inside guides. • The media is taut and parallel with itself and the pathway when wound onto the rewind spindle/core. 9. Close the printhead. 10. To discard the label backing from the rewind spindle, refer to .Removing the Label Backing Material” on page 38. Brady X-PLUS Series User.s Guide MediaguideMediaMediasupplyguideClosedOpenRewindspindleHookPrintheadleverRewindplateTear-off/ peel-offbarGuideplateLabelLabelbackingMediaguideMediaMediasupplyguideClosedOpenRewindspindleHookPrintheadleverRewindplateTear-off/ peel-offbarGuideplateLabelLabelbacking Figure 17 Brady X-PLUS Series User.s Guide Rewind Mode (for Printers Without the Cutter Option) NOTE: Rewind option required. Refer to Figure 18. 1. Remove the rewind plate from its storage location in front of the print mechanism inside the media compartment. 2. Invert the rewind plate so that the lip on the attached hook plate points down. 3. Insert the hook plate lip a short distance (."/13 mm) into the lower opening in the side plate. 4. Align the upper end of the rewind plate with the corresponding opening in the side plate. Slide in the rewind plate so that it stops against the printer.s main frame. 5. Open the printhead. 6. Slide the media guide and media supply guide as far from the printer frame as possible. Flip down the media supply guide. 7. Load media as shown. 8. When loading media, allow approximately 36” (914 mm) of media to extend past the printhead. Remove all labels from this portion to create a leader. 9. Remove the hook from the rewind spindle. If you are using a core, slide it onto the rewind spindle until it is flush against the guide plate. 10. Wind the label backing around either the 3” (76 mm) core or the rewind spindle and reinstall the hook. 11. Flip up the media supply guide. Slide in the media guide and media supply guide so they just touch, but not restrict, the edge of the roll. Brady X-PLUS Series User.s Guide Before closing the printhead, make sure: • The media is positioned against the inside guides. • The media is taut and parallel with itself and the pathway when wound onto the rewind spindle/core. 12. Close the printhe...
Este manual também é adequado para os modelos :Impressoras - 203X-PLUS (1.26 mb)
Impressoras - 600X-PLUS (1.26 mb)
Impressoras - and 360X-PLUS (1.26 mb)