Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
(Fo. Serial-Interfac. Printer. Only. The M-Series Printer, with the RS-232 Serial Interface, uses eight miniature switches located on the rear of the printer, above the Signal Interface Cable Connector. The ON/OFF positions of these switches establish some of the Printer Configuration Parameters. Bank 1 switches must be properly positioned to establish serial data communications with the host computer. Thereafter, the position of these switches should not be changed. Note: Parallel-interface printers do not require these configuration parameters, therefore they have no Bank 1 switches. If these switches are in the proper position to match the communication configuration of the host computer, and the printer is not receiving data, refer to the Interconnections Section and make sure the correct interface cable is being used. Note: The printer is fixed at 1 stop bit, so make sure that your host device is also set at 1 stop bit. Ban. . (Serial-Interfac. Printer. Only. Switch 3 2 1 Baud Rate R R R 9600 baud R R L 19200 baud R L R 110 baud R L L 300 baud L R R 600 baud L R L 1200 baud L L R 2400 baud L L L 4800 baud Switch 4 Data Bits (Must be set to 8 Data Bits to use Code Page 850.) R 7 Data bits L 8 Data bits Switch 6 5 Parity (If you choose 7 data bits, you must choose either even or odd parity.) R R Even parity R L Parity disabled L R Odd parity L L Parity disabled Switch 7 Communication Handshake Control R XON/XOFF control L DTR/DSR control Switch 8 Error Detection Protocol R No error detection L Error detection active Tabl. 4.. M-SeriesUser.sGuideConfigurationandCalibrationM-SeriesUser.sGuideConfigurationandCalibration Ban. . (260. Printer. Only. These switches can manually override any ZPL II commands that affect print mode, media mode, and media type. They can also override settings established during the calibration procedure. Reasons why would might want to use these override switches: • Troubleshooting. By using these Ban. . (260. Printer. Only. Switch 3 2 1 Print Mode R R L Reserved R L L Tear-Off L R L Peel-Off L L L Rewind -R Override is disabled Switch 6 5 4 Media Mode R R L Black-mark sensing mode R L L Transmissive sensing mode with non-continuous media (detects a web/notch) L L L Transmissive sensing mode with continuous media -R Override is disabled Switch 8 7 Media Type R L Thermal transfer L L Direct thermal -R Override is disabled switches, you know beyond a doubt what operating mode your printer is in. • Lets you use a single ZPL II label format for many different printers—without worrying if the format contains a mode command that is inappropriate for your printer configuration. • Some third-party label design software packages work better if these switches control the mode. If you do not want to override ZPL II or the calibration settings, disable one or more of the override options by setting switches 1, 4, and/or 7 to the R (OFF) position and turning the power ON. With these disabled, the 260M will require ZPL II commands and/or re-calibration to set print mode, media mode, and/or media type. To override, set the switches to one of the modes shown in the table. If you are in the process of printing, this change takes effect on the next label printed. If you change the switches from active to disabled after printer power-up, the printer remains in the current mode until a ZPL II Tabl. 4.. command or re-calibration changes the mode. ConfigurationandCalibrationM-SeriesUser.sGuideConfigurationandCalibrationM-SeriesUser.sGuide Configuratio. Mod. The Configuration Mode allows you to fine-tune the internal printer configuration settings for your application. In this mode, you can change the following parameters: • Printing darkness • Rest position of the media with respect to the “web” or “ interlabel gap” • Position of printing relative to the top of the label • Media and Ribbon Sensor values • Label length • Printing method • Media type (continuous or non-continuous) You can get a printout of the printer configuration (the values for each of these parameters) at any time by performing the CANCEL Key Self Test (See Chapter 3). If it is ever necessary to reset the printer configuration to the factory defaults, refer to the “FEED Key and PAUSE Key” Self Test description in Chapter 7. The ZPL II Programming Guide contains information on instructions which may be sent to the printer to disable the MODE key and set specific label format values for each of these parameters. If you are not using ZPL II, refer to the instructions provided with your software package to determine if you also have this capability. Calibratio. IMPORTANT: Perform the Calibration Procedure when media and ribbon are first installed and each time a different type of media or ribbon is installed. During this procedure, the printer automatically determines the media type, label length, media and ribbon sensor settings, and printing method. Media type is determined by sensing either continuous or non-continuous media as blank ...
Este manual também é adequado para os modelos :Impressoras - 200M (1.46 mb)