Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
Refer servicing to qualified personnel. Power source_ Warning • The power source voltage of this unit is listed on the nameplate. Only plug the unit into an outlet with the proper voltage. • When you operate this equipment, the outlet should be near the equipment and accessible. • To ensure safe operation the AC cord supplied must be inserted into standard three-prong AC outlet which is effectively grounded (earthed) through the normal wiring. • The fact that the equipment operates satisfactorily does not imply that the power point is grounded (earthed) and that the installation is completely safe. For your safety, if in any doubt about the effective grounding (earthing) of the power point, consult a qualified electrician. • If the plug cannot be inserted into the AC outlet, contact a licensed electrician to replace the outlet with a properly grounded (earthed) one. Do not defeat the purpose of the grounding (earthing) plug (ex. do not use a conversion plug). Laser safety_ Caution • This printer utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Ozone release Warning • Make sure that the printer is installed in a well ventilated room so as not to increase density of ozone in the air. Since ozone is heavier than air, it is recommended that air at floor level be ventilated. 10 Moving the unit The printer weighs approximately 17 kg {37.4 lbs.}. The back of the printer should be facing you when you move it. Turn the power off and remove the power cord when handling the unit. Caution labels (220-240 VAC equipment) Laser diode properties Laser output : 5 mW max Wavelength : 780 nm Emission duration : Continuous -A i CAUTION : HOT SURFACE 28-79 ATTENTION : TEMPÉRATURE ELÉVÉE BSiiE VORSICHT : HEISS PRECACION/ATTENZIONE : ALTA TEMPERATURA 11 FOR USERS IN U.K. IMPORTANT: FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY This printer is supplied with a moulded three pin mains plug each for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSI to BS 1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET. If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt please consult a qualified electrician. WARNING: THIS APPLIANCE MUST BE EARTHED. IMPORTANT: The wires in this mains lead are coloured in accordance with the following code. Green-and-Yellow: Earth Blue: Neutral Brown: Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol , or coloured GREEN or GREEN-AND-YELLOW. ^ The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED. How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse. SCREWDRIVER. „ „ _ FUSE COVER 12 Chapter 1 Before You Start Cautions To avoid problems, do not use the equipment under the following conditions: в • Direct exposure to sunlight • Extremely high or low temperature [temperature range: 10”C to 32.5°C (50°F to 90.5°F)] • Extremely high or low humidity (humidity range: 30% to 80% RH) • Condensation due to rapid change of temperature • Areas of poor ventilation • Areas of high dust or chemical fume concentration (solvent etc.) • Unstable or unlevel surfaces Directly in front of air conditioning vents • Do not keep liquids near the printer. Accidental spills of liquid into the printer can cause severe damage. • Too much media/ document which exceeds the limit mark on the guide of the tray. • Top/Rear covers opened while the printer is operating; it may cause a media jam. Not genuine toner • Any toner other than genuine Panasonic toner. It may damage the printer. 4 13 Cautions Features of the KX-P7500 Series Before You Start Static electricity damage__ To prevent static electricity damage to any of ...