Recording part (black density: .3) is . or more. • Testing conditions: -Light resistance: 1000 hours under 5000 LUX of fluorescent light -Moisture resistance: +40.C, 90% RH. 24 hours -Heat resistance: +50.C, 24 hours • PREcAUTionS • Avoid locations of high temperature and high humidity • Do not expose paper to direct sun light for an extended period • Do not use solvent paster • Do not contact plasticizer • Do not contact diazo copy paper immediately after copying • Protect from wetting and scra

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, wh

Signal I/O Contents No. Signal I/O Contents 1 PRSTB I Data strobe 2 PRSTB-RET — Connected to logic GND 3 PRDT0 I Data 0 4 PRDT0-RET — Connected to logic GND 5 PRDT1 I Data 1 6 PRDT1-RET — Connected to logic GND 7 PRDT2 I Data 2 8 PRDT2-RET — Connected to logic GND 9 PRDT3 I Data 3 10 PRDT3-RET — Connected to logic GND 11 PRDT4 I Data 4 12 PRDT4-RET — Connected to logic GND 13 PRDT5 I Data 5 14 PRDT5-RET — Connected to logic GND 15 PRDT6 I Data 6 16 PRDT6-RET — Connected to logic GND 17 PRDT7 I D

ShElF liFE oF UnPRinTEd PAPER Storage conditions: • Store in dark place at 23.C and 50% RH without removing original packaging (not in direct sunlight) • Do not store in area that maybe subjected to the presence of NOx, SOx, or Ozone Under the above conditons, we guarantee the original image development capability at time of manufacture will be maintained for 5 years minimum. 2. iMAgE liFE AFTER dEVEloPMEnT Storage conditions: • Store in dark place at 23.C and 50% RH (not in direct sunlight) • M

FTP-622DCL/DSL 4. Connector for paper near end detection (CN5) Part number : B2B-PH-K-S (J.S.T) Mating connector part number : PHR-2 (J.S.T) or equivalent No. Signal I/O Contents No. Signal I/O Contents 1 +5 V — Power for logic (+5 V) 2 NES I Paper near end detect signal 5. Connector for stepping motor drive (CN13) Part number : B4B-PH-K-S (J.S.T) No. Signal I/O Contents No. Signal I/O Contents 1 MT/B O Stepping motor coil excitation 2 MT/B O Stepping motor coil excitation 3 MT/A O Stepping moto

Ablagefach Haken Stift (innen) Einstellung der SCSI-ID und des SCSI-Abschlusses In der Werkseinstellung ist die SCSI-ID 5 eingestellt. Die SCSI-ID kann im Einrichtungsmodus des Bedienfelds eingestellt werden. So andern Sie die SCSI-ID: 1 Schalten Sie das Gerat ein, indem Sie auf die mit ”I” gekennzeichnete Seite des Netzschalters drucken (siehe Abbildung 1.1). Der Scanner gibt auf der LCD-Anzeige die Meldung ”Scanner Ready” (Scanner bereit) aus. 2Drucken Sie jetzt die Taste ”Next”. Der Scanner z

0 will maintain its legibility for 5 years minimum. Fujitsu Components International Headquarter Offices Japan Europe Fujitsu Component Limited Fujitsu Components Europe B.V. Gotanda-Chuo Building Diamantlaan 25 3-5, Higashigotanda 2-chome, Shinagawa-ku 2132 WV Hoofddorp Tokyo 141 8630, Japan Netherlands Tel: (81-3) 5449-7010 Tel: (31-23) 5560910 Fax: (81-3) 5449-2626 Fax: (31-23) 5560950 Email: promothq@fcl.fujitsu.com Email: info@fceu.fujitsu.com Web: Web: emea.fujitsu.com/components/ north an