Assessments - , GPA: ( )

Instruções de Operação Hoshizaki, Modelo AM-50BAE-AD

Fabricante : Hoshizaki
Arquivo Tamanho: 1.57 mb
Arquivo Nome : 93c8cca3-aa80-4847-8f8e-45a3406618c6.pdf

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

Remove hinge (C2) from the bottom right part of the door, flip it and reattach to the top left. See Fig. 15. Proceed to step 7. d) Remove hinge (B) from the right side of the unit and the 2 filler screws from the left side. Attach the 2 filler screws to the right side and attach hinge (B) to the left side. See Fig. 13. e) Rotate the top panel 180° from its previous position. This brings the notch that was previously in the right rear to the left front. See Fig. 14. Hook the rear part of the panel on the body, then secure the front with the 2 screws removed in step 6a. 6) If you would like to reverse the door hinges, do the following: a) Contact your local distributor to purchase Hoshizaki Kit HS.0229. The kit contains "hinge (A)-left." b) Remove the 2 screws securing the top panel, then lift it off. See Fig. 11. c) Remove hinge (A)-right and the bracket from the right side of the unit. Set aside hinge (A).right; it is not needed. Remove the top brace from the left side. Fasten hinge (A)-left and the bracket to the left side and the top brace to the right side. See Fig. 12. Note: When on the proper side, the gasket notch for hinge (A) is to the inside. Fig. 11 Fig. 13 Hinge (B) Filler Screws Top Panel Notch Fig. 14 Top Panel Fig. 12 Hinge (A)-Left Bracket Screw Top Brace Gasket Notch Screw Hinge (C1) Hinge (C2) Fig. 15 Hinge (A)-Right Not Needed Screws Screws Screws 7) Remove the bushings from hinge (C1) and hinge (C2) (the hinges attached to the door). See Fig. 16. 8) Remove the gasket from the door. See Fig. 17. Hinge Bushing Gasket Fig. 16 Fig. 17 9) Temporarily fasten the overlay panel to the door using 2 of the M4.25 pan head screws provided. See Fig. 18. CAUTION Ensure that the back surface of overlay panel is flat before attaching. 10) Mark the centerpoint of the hinge (C1) and hinge (C2) holes that extend over the overlay panel. See Fig. 19. Screws Hinge Mark the center point. Door Overlay Panel Fig. 18 Fig. 19 11) Remove the overlay panel from the door. 12) Drill 3/8" diameter holes 1/4" (7 mm) deep where you marked on the overlay panel to accommodate the hinge (C1) and hinge (C2) bushings. 20 21 Snug the screws, but do not tighten. Sheet Metal Bracket Overlay Panel Tighten the screws. 5) Fasten the overlay panel to the door using the four M4.25 pan head screws provided. Snug the screws, but do not tighten. See Fig. 24. 6) Fasten the sheet metal bracket to the bottom of the door with the three T2 screws provided. Tighten the screws to the door. See Fig. 25. 3) Adjust the sheet metal bracket so that it is flush with the bottom of the door. See Fig. 22. 4) Remove the overlay panel from the door and tighten the two M4.8 truss head screws securing the sheet metal bracket to the overlay panel. See Fig. 23. (4) Attachment of Overlay Panel to Door 1) Fasten the sheet metal bracket to the overlay panel using the two M4.8 truss head screws provided. Snug the screws, but do not tighten. See Fig. 20. 2) Temporarily fasten the overlay panel to the door using 2 of the M4.25 pan head screws provided. See Fig. 21. Sheet Metal Bracket Door Sheet Metal Bracket Screws Overlay Panel Door Screws Fig. 20 Fig. 21 Overlay Panel Snug the screws, but do not tighten. Sheet Metal Bracket Fig. 22 Fig. 23 Fig. 24 Fig. 25 22 7) Tighten the four M4.25 pan head screws installed in step 5. See Fig. 26. 8) Replace the door gasket in its proper orientation. Reinsert the bushings into hinge (C1) and hinge (C2) (the hinges attached to the door). See Fig. 27. Canoe Clips Fig. 26 Tighten the screws. Bushing Bushing Gasket Fig. 27 9) Attach the door to hinge (A), then continue to maintain a hold on the door. Screw the hinge stop pin into hinge (B) until it is tight. See Fig. 28. 10) Insert the 2 canoe clips included in the accessory bag into the holes on top of the door. See Fig. 29. Hinge Stop Pin Hinge (B) Fig. 28 Fig. 29 Door D. Setup 1) Position the icemaker in the selected permanent location. 2) Level the icemaker from side-to-side and front-to-rear by adjusting the feet. E. Electrical Connection WARNING 1. Electrical connection must meet national, state, and local electrical code requirements. Failure to meet these code requirements could result in death, electric shock, serious injury, fire, or severe damage to equipment. 2. This unit requires an independent power supply. See the nameplate for proper voltage and breaker/fuse size. Failure to use a proper breaker or fuse can result in a tripped breaker, blown fuse, or damage to existing wiring. This could lead to heat generation or fire. 3. THIS UNIT MUST BE GROUNDED: This unit is equipped with a 3-prong grounding plug to reduce the risk of potential shock hazards. It must be plugged into a properly grounded, independent wall outlet. If the outlet is a 2-prong outlet, it is your personal responsibility to have a qualified electrician replace it with a properly grounded, independent 3-prong wall outlet. Do not remove the ground prong from the power cord and do not use an adapter plug...