Assessments - 3, GPA: 4 ( )

Fabricante : Southbend Arquivo Tamanho: 1.52 mb Arquivo Nome : Língua de Ensino:

The carrier should arrange an inspection. Be certain to hold all contents plus all packing material. 1. Uncrate carefully. Report any hidden damage to the freight carrier IMMEDIATELY. 2. Do not remove any tags or labels until unit is installed and working properly. Step 2: Attach Countertop Legs, Mount on Counter, or Mount on Stand The appliance can be mounted in several ways: To mount it on short, countertop legs, go to Step 2a on page 10. To mount it directly on a countertop, go to Step 2b on page 11. To mount it on an insulated base on a countertop, go to Step 2c on page 12. To mount it on a stand that rests on the floor, go either to Step 2d on page 13 (for 24", 36", and 48" models) or to Step 2e on page 15 (for 60" and 72" griddle models). INSTALLATION OWNER’S MANUAL 1182845 REV 8 PAGE 9 INSTALLATION HEAVY DUTY COUNTERLINE PAGE 10 OWNER’S MANUAL 1182845 REV 8 INSTALLATION Step 2a: Installation on Countertop Legs To install the appliance using countertop legs, do the following: 1. Locate the box of four legs shipped with the appliance (if countertop legs were ordered). 2. Raise the appliance about 6" so that the legs can be screwed into the bottom near the corners. Lift the appliance only from the ends, never from the middle! Support the lifted appliance so that it will not fall while you are attaching the legs. 3. Screw the four legs into the threaded holes located on the bottom of the appliance near each corner (as shown in Figure 5 below). 4. Gently lower the appliance onto the counter. Level the appliance surface by screwing one or more of the legs in or out. 5. Go on to Step 4 on page 18. Figure 5 HEAVY DUTY COUNTERLINE INSTALLATION Step 2b: Installation Directly on a Non-Combustible Countertop Surface The appliance may be installed directly onto a flat NON-COMBUSTIBLE surface, as follows: 1. Place the appliance in the position that it will be used. Lift the appliance only from the ends, never from the middle! 2. Connect the gas supply (see Step 4 on page 18), then return to this procedure. 3. Check that the appliance is in the position you want it to be in. 4. Seal the appliance to the countertop using G.E. or Dow Corning RTV, or the equivalent (as shown in Figure 6 below). Consult local codes for exact requirements. A small bead of RTV around all four bottom edges should be adequate. Open the front door to seal along the front edge of the frame. 5. Go on to Step 5 on page 19. Figure 6 INSTALLATION OWNER’S MANUAL 1182845 REV 8 PAGE 11 INSTALLATION HEAVY DUTY COUNTERLINE INSTALLATION Step 2c: Installation on Insulated Base The appliance may be installed onto a flat NON-COMBUSTIBLE (but heat sensitive) surface using the optional insulated base, as follows: 1. Attach the side pieces of the insulated base (items “A” in Figure 7 below) to the front piece (item “B”) using the four sheet metal screws provided. 2. Position the insulated base on the surface where you want the appliance to be located. 3. Position the appliance on top of the insulated base. Lift the appliance only from the ends, never from the middle! 4. Go on to Step 4 on page 18. Figure 7 A B PAGE 12 OWNER’S MANUAL 1182845 REV 8 HEAVY DUTY COUNTERLINE INSTALLATION Step 2d: Installation on Floor Stand (24", 36", and 48" Models) The 24", 36", and 48" appliances may be installed on top of an optional floor stand (for 60" and 72" griddles, go to Step 2e on page 15). The floor stand is shipped in a separate crate and must be assembled, as follows: 1. Position the bottom-brace pieces on a flat surface, as shown in Figure 8 below. There are two bottom- side braces (items “A”), a bottom-front brace (item “B”), and an identical bottom-rear brace (item “B”). 2. Position a corner brace (item “C”) in each corner, matching the pre-punched holes on the lower inside flange of the bottom braces. 3. Position a leg bracket (item “D”) into each corner. Be sure that the bracket flanges are engaged into the open hem of the bottom braces. 4. Use the sixteen 1/2"-long hex head bolts (items “E”), lock washers (items “F”), and acorn nuts (items “G”) to bolt the corner braces to the bottom braces. Only hand-tighten for now. 5. Check that the leg brackets are in the proper position, and that the outside corners are square. Figure 8 G F E A D C B D C A 6. Use the eight 1-1/2" hex bolts (items “H” in Figure 9) to attach the two left-legs (items “I”) and the two right-legs (items “J”). “Left” and “right” are as seen from the front or rear of the stand. Be sure that the small threaded-insert near the top of each leg faces either the front or the rear of the stand, not a side. Insert the bolts through the leg brackets and into the legs. Only hand-tighten the bolts for now. INSTALLATION OWNER’S MANUAL 1182845 REV 8 PAGE 13 INSTALLATION HEAVY DUTY COUNTERLINE Figure 9 INSTALLATION N O I J H J I L M L K 7. Check the partially assembled stand to make sure that the legs are straight and that all corners are square. Now tighten all bolts, but do not over tighten. 8. If legs wi...

Baixe o seu

Para fazer o download, introduza 2 dígitos :