Assessments - 2, GPA: 4 ( )

Fabricante : Bakers Pride Oven Arquivo Tamanho: 3.2 mb Arquivo Nome : Língua de Ensino:

8. Complete the line up by slipping the Counter Top Joint Cover over the end flanges of the adjoining counter tops. Kick Plate Mounting A black vinyl-covered kick plate is provided for the front and back of each case. 1. Slide the front kick plate (the wider of the two) behind the lower finished front panel of the case (see Figure 2). 2. Make certain that the ends of the kick plate are flush with the ends of the lower finished front panel and that the kick plate is flush to the floor. 3. Drill 5/32” diameter holes in the case base to match the pre-drilled holes in the kick plate. 4. Attach the kick plate to the case base with the black sheet metal screws provided. 5. Mount the back kick plate to the case in the same manner. 6. Place the End Kick Plates in position (see Figure 2). NOTE: There are left and right hand parts. The longer end flange faces toward the front of the case with the black side out. The End Kick Plates fit over the ends of the front and back kick plates and flush to the floor. 10 Hot Food Deli Case Installation 11 End Panel Mounting 1. Now, attach the End Trim Panels to the base ends. The studs on the Trim Panels pass through the mounting holes in the base ends (see Figure 2). Both End Trim Panels are the same. 2. The panels are secured from inside with the #10 Pal Nuts provided. 3. Attach the End Panels to the ends of the case(s) as shown in Figure 2 using the shoulder screws provided. For Glass End Panels only, slide the plastic bushings provided over the shoulder screws before inserting the screw into the glass panel. Be careful that the screws do not bind in the holes in the glass panel. NOTE: If the ends are already attached to the case, the End Kick Plates can be lowered to the floor. To do this loosen the End Trim Panel nuts from inside the case then slide the Kick Plates flush with the floor and tighten the Trim Panel nuts. 4. These cases are to be sealed to the floor if required by local health codes. Seal the kick plates to the floor using a silicone-type sealant (Dow Corning RTV #732 or equivalent). Figure 2. Floor Model - End Kick Plate & End Panel Mounting Hot Food Deli Case Installation 12 Pedestal Model Pedestal mounted cases are provided with a mounting frame that runs the full length of the case. This allows the pedestals to be located at any point along the length of the case. Each case should be supported by at least two pedestals. One pedestal can support the ends of two adjoining cases. If in doubt, consult the factory for assistance in determining the proper pedestal locations for your particular installation. FRONT COVER (PAINTED or STAINLESS) FITS OVER REAR COVER BOLT FRAMES OF ADJOINING CASES TOGETHER AT THESE (3) LOCATIONS MOUNTING RAILS ON CASE FIT INSIDE PEDESTAL ENDS PEDESTAL FRAME REAR COVER (PAINTED or STAINLESS) INSTALL FIRST RETAINING CLIP CLAMPS PEDESTAL FRAME TO BOTTOM FLANGE OF CASE FRAME RAISE LOWER LEG LEVELER LEVEL CASE Figure 3. Pedestal Model - Leveling and Cover Attachment Leveling Deli cases must be installed level to insure proper operation and alignment to adjoining equipment. Use a carpenter’s level as shown in Figure 3. Begin lineup leveling from the highest point of the store floor. 1. Level the case using the leg levelers at the corners of the pedestals (see Figure 3). 2. Raise the low end of the case to level it, do not lower the high end. 3. Check for level side-to-side and front-to-back. 4. If you are installing adjoining cases, position the next case in line beside the level case and proceed to the next step. 5. Level this case in the same manner. 6. When level, bolt the two cases together at the locations shown in Figure 3. If the cases have been properly leveled, the front panels and counter tops should align with a small, uniform gap between the front panels of the two cases. Hot Food Deli Case Installation 13 7. Proceed in the same manner until all the cases in the line are level and bolted together. 8. Complete the line up by slipping the Counter Top Joint Cover over the ends flanges of the adjoining counter tops. Front and Rear Cover Attachment 1. Slide the Rear Cover over the Pedestal Frame first (see Figure 3). Then slide the Front Cover over the Frame with the sides of the Front Cover lapping over the side of the Rear Cover. The Front Cover will extend approximately 4-1/2” from the front of the frame. 2. Drill two 5/32” diameter holes in each side of the Pedestal Frame to match the predrilled holes in the covers. 3. Secure the covers to the frame using the #8 sheet metal screws provided. 4. These cases are to be sealed to the floor if required by local health codes. Seal the pedestal covers to the floor using a silicone-type sealant (Dow Corning RTV #732 or equivalent). End Panel Mounting Figure 4. Pedestal Model - End Panel Mounting 1. Attach the End Panels to the ends of the case(s) as shown in Figure 4 using the shoulder screws provided. For Glass End Panels only, slide the plastic bushings provided over the shoulder screws...

Baixe o seu

Para fazer o download, introduza 2 dígitos :