Assessments - 3, GPA: 3.7 ( )

Fabricante : GE Arquivo Tamanho: 603.54 kb Arquivo Nome : Língua de Ensino:

NOTE: Disconnect electric power to disposer circuit before installation. Turn the circuit breaker to the OFF position or remove the fuse. A. Connect the disposer to 110–120 Volt, 60 Hz AC current only. Consumer SupportTroubleshooting TipsInstallation InstructionsSafety Instructions Operating Instructions B. If a plug-in cord is used, use a three- prong plug. Ground wire should be attached to the ground screw in the bottom of the disposer (end bell). Trace lead connected to this blade and attach that lead to white wire on disposer. Ribbed Side NOTE: When viewing face of electrical plug with grounding pin at top, the larger left blade is connected to the identified wire. C. Use a cable clamp strain relief connector where Strain Relief power cord enters the disposer. Nut To Wire Your Disposer Directly into the House Current: GROUNDING INSTRUCTIONS: This appliance must be connected to a grounded, metal, permanent wiring system; or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. A. If you use BX cable: 1. Install the cable connector in the hole. 2. Connect white wire to white lead of disposer. 3. Connect black wire. 4. Connect bare ground wire. If BX cable is not used, provide a separate ground wire to nearest reliable ground, using the screw in the end bell for the ground wire. Red Reset Button Ground Screw Wire Nuts To House Current Remove or Power Cord Cover Plate Bottom of the Disposer (end bell) B. If your power supply does not include a ground wire, you must provide one unless metal cable is used. Attach a copper wire securely to disposer ground screw and attach other end of wire to a reliable ground. Use only UL approved ground clamp. If plastic pipe is used in your home, a qualified electrician should install a proper ground. READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY. SAVE THESE INSTRUCTIONS 3 Installation Instructions Disposer If you have questions, call 1-800-GECARES or visit our Website at: BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT – Save these instructions for local inspector’s use. • IMPORTANT – Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer. • Note to Consumer – Keep these instructions for future reference. • Skill level – Installation of this appliance requires basic mechanical skills. • Completion time – 1 hour • Proper installation is the responsibility of the installer. • Product failure due to improper installation is not covered under the Warranty. ADDITIONAL MATERIALS YOU MAY NEED • Steel punch or wooden dowel • Petroleum jelly or liquid soap • Hose clamp • Dishwasher drain connector • Adjustable pipe wrench • Plumber’s putty (for cast sinks) • Stepped rubber drain adapter • Wire nuts • Cable connector • Flexible drain pipe • Power cord kit (Part Number PM3X215GDS) WHAT YOU WILL NEED • Phillips and flat blade screwdrivers • Channel lock pliers, slip joint • Hammer • Nut driver PREPARATION 1. Disconnect electrical power supply to disposer. 2. Remove old disposer or sink flange assembly. 3. Inspect drain line. If it is heavily coated with hardened grease and accumulations, rout out with a plumber’s snake. 4. Remove old sealing materials and gasketing from sink opening, both top and bottom. NOTE: Top and bottom of sink surfaces must be free of any materials to prevent leaks. Installation Instructions COMPONENTS AND INSTALLATION 1 COMPONENTS INSTALLATION OF SINK FLANGE (Read completely before starting.) Sink Flange Rubber Gasket SinkFiber Gasket Support Ring Open Area No Obstruction Sink Flange Mount Ring should be free to move up and down *Stopper *Removable Splash Guard Sink Flange Rubber Sink Flange Gasket Groove Dishwasher Discharge Inlet Elbow Gasket Hopper Sink Fiber Gasket Support Ring (Note Arrows Indicating Up) Screws Discharge Elbow Elbow Flange Mount Ring Rating Label in This Area Tightening Ears End Bell (Electrical Connections) Cushion Mount *Not used with batch feed model Sink Flange Assembly Disposer Correctly Installed Sink Flange Bottom Bead of Cushion Mount Cushion Mount Groove Bottom Bead (shown for proper orientation) NOTE: Pay close attention to the order of the sink flange parts, as they have been correctly assembled by the factory. A. Disassemble the sink flange assembly from the disposer by turning the mount ring to the left (clockwise) and removing it. B. Raise the mount ring toward the top of the sink flange. Remove the cushion mount and the mount ring. You may want to practice installing the cushion mount at this point before you are under the sink. C. Unscrew the support ring from the sink flange and remove the fiber gasket. You are now left with the sink flange and the rubber gasket. D. The rubber gasket is used instead of plumbers putty with stainless steel sinks. Some cast sinks will require putty. E. If no putty is used, insert ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :