Assessments - , GPA: ( )

Instruções de Operação Hoshizaki, Modelo AM-150BWF

Fabricante : Hoshizaki
Arquivo Tamanho: 1.06 mb
Arquivo Nome :

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

3. Always wear liquid-proof gloves for safe handling of the cleaning and sanitizing solutions. This will prevent irritation in case the solution comes into contact with skin. [a] WATER SYSTEM 1) Dilute approximately 5 fl. oz. (148 ml) of recommended cleaner Hoshizaki “Scale Away” or “LIME-A-WAY” (Economics Laboratory, Inc.) with 1 gal. (3.8 lit.) of water. 2) Remove all ice from the Evaporator and the Storage Bin. Note: To remove cubes on the Evaporator, remove the Front Panel (Lower), move the Control Switch on the Control Box to the “OFF” position and move it back to the “ICE” position after 3 minutes. The defrost cycle starts and the cubes will be removed from the Evaporator. 3) Move the Control Switch to the “OFF” position. Close the Water Supply Line Shut-off Valve. 4) Remove the Water Tank to drain the water. Refit the Water Tank in its correct position. 5) Slowly pour the cleaning solution into the Water Tank. 6) Move the Control Switch to the “WASH” position. 7) After circulating the cleaning solution for about 30 minutes, move the Control Switch to the “OFF” position. 12 8) Remove the Water Tank to drain the cleaning solution. Refit the Water Tank in its correct position. 9) Open the Shut-off Valve. 10) Move the Control Switch to the “WASH” position to circulate clean water for about 5 minutes. 11) Move the Control Switch to the “OFF” position and immediately back to the “WASH” position to rinse water. 12) Repeat the above rinse procedure three more times to rinse thoroughly. 13) Dilute approximately 0.5 fl. oz. (14.8 ml) of 5.25% Sodium Hypochlorite (Chlorine Bleach) with 1 gal. (3.8 lit.) of water. 14) Move the Control Switch to the “OFF” position. Close the Water Supply Line Shut-off Valve. 15) Remove the Water Tank to drain the water. Refit the Water Tank in its correct position. 16) Slowly pour the sanitizing solution into the Water Tank. 17) Move the Control Switch to the “WASH” position. 18) After circulating the sanitizing solution for about 15 minutes, move the Control Switch to the “OFF” position. 19) Remove the Water Tank to drain the sanitizing solution. Refit the Water Tank in its correct position. 20) Open the Shut-off Valve. 21) Move the Control Switch to the “WASH” position to circulate clean water for about 5 minutes. 22) Move the Control Switch to the “OFF” position and immediately back to the “WASH” position to rinse water. 23) Repeat the above rinse procedure two more times to rinse thoroughly. 24) Move the Control Switch to the “ICE” position, and start the automatic icemaking process. Refit the Front Panel (Lower) in its correct position. 13 14 [b] STORAGE BIN, SLOPE, SCOOP, ETC. IMPORTANT 1. Wash your hands before removing ice. Use the Plastic Scoop provided to remove ice. 2. Keep the Scoop clean. Clean it by using a neutral cleaner at least once a day, and rinse thoroughly. 3. Close the Bin Door after removing ice to prevent entrance of dirt, dust or insects into the Bin. 4. Clean the Bin Liner at least once a month by using a neutral cleaner. Rinse thoroughly after cleaning. 5. The Storage Bin is for ice use only. Do not store anything else in the Bin. 6. Keep the area around the icemaker clean. Dirt, dust or insects in the icemaker could cause electrical damage to the equipment or harm to individuals. 1) Remove the Front Panel (Lower), and move the Control Switch on the Control Box to the “OFF” position. 2) Unplug the icemaker. 3) Open the Bin Door, and remove ice from the Storage Bin. 4) Remove the Slope by bending its center carefully and releasing it from the two Slope Shafts. Take out the Slope from the Storage Bin. 5) Thoroughly clean and sanitize the Storage Bin, Slope, Scoop and any parts normally accessible from the Storage Bin. 6) Remove each Separator by lifting it to the horizontal position and pushing it hard inward. Remove all the Separators in the same way, and clean and sanitize them. 7) Disconnect the Suction Tube from the Water Tank to drain the Tank. Water Tank Suction Tube Separator 15 8) Remove the Thumbscrews on both sides of the Water Tank, and pull it out toward you. Clean and sanitize the Water Tank. 9) Pull the Discharge Tube from the Water Plate. Remove the Water Plate by pulling it toward you. 10) Remove the Caps to clean and sanitize the Water Plate. If the Nozzles are clogged, clean them with a wire or a suitable brush. 11) Refit the Caps on the Cleaning Outlets to seal them off. 12) Slide in the Water Plate along the Mechanism Base. Refit the Discharge Tube securely on the Spray Outlet. A loose fitting may cause a water leak. 13) Place the rear of the Water Tank on the Water Tank Rest at the back of the Storage Bin. Use the Thumbscrews to secure the front of the Water Tank to the Mechanism Base. 14) Refit the Suction Tube on to the Water Tank Inlet. A loose fitting may cause a water leak. Discharge Tube Water Plate Cap Water Plate Cap Water Plate Water Tank Suction Tube Discharge Tube Water Plate Mechanism Base Bin Rear Tank Rest Thumbscrew Wa...