Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
See sections ‘Placing the tap unit onto the keg’ and ‘Placing the tube into the tap unit’ in this chapter. 1 Slide the release button to the right to open the doors. 2 Lift the two blue locking levers completely. 3 Tilt the keg with the assembled tap unit slightly forward and put it into the appliance. First put the keg on the cooling plate of the appliance. Then put the keg upright by sliding the tap unit between the blue locking levers. 4 Push down the blue locking levers until they are in horizontal position. If you are unable to put the locking levers in horizontal position, you have not put the keg into the appliance in the right position. Take out the keg and follow steps 1 to 3 again. After you have installed the keg (even the first time), the pump runs for a few seconds. 5 Close the doors. -- , English 11 1 EnglisH cooling After you have installed the keg, the appliance automatically star ts to cool the keg. Note: At an ambient temperature of 23°C, chilling an uncooled keg takes 1215 hours. Tip: If you want to pour beer shortly after placing the keg in the appliance, prechill the keg in upright position in the fridge for a while before you install it. For more tips, see chapter ‘Troubleshooting’. 1 Wait until the beer has reached the right drinking temperature. HD3620:The temperature is shown on the display in green (see , section ‘LCD display’ in this chapter). HD3610:The temperature light lights up green (see section ‘LED , indicator lights’ in this chapter). lcD display (HD3620 only) The display shows the temperature of the beer, the beer level inside , the keg and the freshness of the beer. temperature indication Wait until the temperature of the keg has dropped below 4°C before you star t to pour beer. The ideal drinking temperature is 3°C. The colour of the temperature displayed tells you if the beer has reached the right drinking temperature. -Red = the beer temperature is not yet ideal for consumption (above 4°C).The beer head may be too large. -Green = the beer has reached the right temperature (4°C or below) for consumption. level indication The yellow-orange level indication on the display shows the amount of beer left in the keg in eight steps. Note: If you use 20cl glasses, you can pour approx. 30 glasses of beer from one keg. If you use 33cl glasses, you can pour approx. 18 glasses. Freshness indication The freshness indication tells you how long the beer is still fresh. EnglisH 1 -When you place a new keg in the appliance, the freshness indication shows that the beer in the keg stays fresh for 30 days.The indication counts down from 30 to 0 days. -Once the keg has been opened, the beer stays fresh for 30 days if the keg is stored in the appliance Make sure the appliance is switched on all the time. -When 30 days have passed, the display shows that the keg needs to be replaced. A dash and an exclamation mark appear on the display. adapting the freshness indication -If you want to switch off the appliance for a longer period (e.g. a holiday), store the opened keg in the fridge. Disconnect the tap unit, rinse the top of the keg, rinse the tube and store the tube with the keg in the fridge. Always write down the date and the number of days that the beer inside the keg is still fresh on the keg (see number of days on the display). -When you reinstall the opened keg, you can set the freshness indicator to the correct number of days with the – and + buttons. Tip:To calculate the correct number of days: compare the date with the one you have written on the keg and subtract the number of days the keg lay in the fridge from the number you wrote on the keg when you stored it. Other indications Besides the beer level and temperature, the display gives the following information: -Green dash with no level indication visible = the tap unit is not present on the keg. -Red dash with no level indication visible = no keg is installed. -Red or green dash with flashing yellow-orange background light = the tap unit and/or tube are not properly placed. Remove the keg and check if the tap unit and the tube are properly placed. See chapter ‘Preparing for use’, sections ‘Placing the tap unit onto the keg’ and ‘Placing the tube into the tap unit’. If this does not help, tr y another keg with a new tube. lED indicator lights (HD3610 only) -There are three indicator lights on top of the appliance that show the status of the appliance. -Red indicator light = the appliance is switched on and you have to install a keg. -Orange indicator light = the appliance is cooling the keg and the keg has not yet reached the right drinking temperature. -Green indicator light = the beer has reached the right drinking temperature and is ready to be poured. 1 EnglisH Other indications Red indicator light flashes = the tap unit and/or tube are not properly placed. How to pour a perfect beer Follow the instructions below to pour a perfect beer. cleaning beer glasses Always use clean beer glasses when you tap beer. 1 Clean the glasses...