Assessments - 5, GPA: 4.2
(
)
)
|
Facilidade de uso
All notices are to be kept in good condition. Replace any unreadable or damaged labels. Site preparation The dispenser must have at least four inches of space behind it. This space is needed for airflow, air filter removal, and cleaning. Minimal clearance is required between the dispenser sides and the wall or another appliance. The dispenser performs better if not placed near any heating appliance. Leave some space so the dispenser can be moved for cleaning. 41084 102709 INTRODUCTION Safety first! To avoid electrical shock, unplug dispenser from power source before servicing inside. WARNING: When powered, the condenser cooling fan will turn on every 30 minutes to aid cooling the entire unit, even when not in the ICE or CHILL modes. KEEP HANDS AWAY FROM FAN! Basic Maintenance In order to maintain proper machine operation, the shaft seals and bushings need to be replaced as a Preventative Maintenance measure. A reminder message will appear every 6 months. Worn/dirty shaft seals/bushings will have a direct effect on torque sensing and prevent complete freezing in “ICE” mode. “UPPER” case vs “lower” case Before beginning the process of troubleshooting, verify simple operating modes, ie; “CHILL” mode will not freeze the product, but “ICE” mode will. You should also observe the letter case size in either mode. UPPER case means the solenoid valve for that side is open, lower case, solenoid is closed. JULY 4, 2002ICEIce Valve closed Valve open Fault codes To aid in troubleshooting, fault codes are now incorporated into the display. See “Troubleshooting”. 41084 102709 TEMP & TORQUE SCREEN Press and hold for five seconds the ULTRA and ICE hidden switches to display the TEMP & TORQUE. The temperature of each cooling drum and the hot gas temperature will toggle back and forth. The auger torque is displayed continuously. Press and release the ULTRA and ICE hidden switches to return to HOME SCREEN. The TEMP & TORQUE mode is typically used for service. DISPLAYTEMP & TORQUE 3025- 161161°h2728°b 3025- NOTICE: While in the TEMP & TORQUE screen, the UPPER/lower case will be replaced by symbols. The indicates the solenoid valve is open, and the indicates that solenoid is closed. 41084 102709 OPERATING CONTROLS ULTRA-1 There are three of these switches that will be used for the operation of the dispenser. 1 2 3 P3932 1. switch (upper left corner of the control pad) This switch is the ON/OFF toggle switch which powers up the dispenser and the LCD display. When ON the Date and Time toggle back and forth continously except during programming. 2. (upper right corner) This is used to turn the auger motor to AUGER ON, AUGER OFF or AUGER REFILL ON. (Refill only applicable when installed) 3. (lower right corner) This is used to turn the ice control to OFF, ICE or CHILL. 41084 102709 OPERATING CONTROLS ULTRA-2 There are five of these switches that will be used for the operation of the dispenser. 1 P3677 2 3 4 5 1. switch (upper left corner of the control pad) This switch is the ON/OFF toggle switch which powers up the dispenser and the LCD display. When ON the Date and Time toggle back and forth continously except during programming. 2. (bottom left corner) This is used to turn the left side auger motor to AUGER ON, AUGER OFF or AUGER REFILL ON. (Refill only applicable when installed) 3. (bottom left corner) This is used to turn the left side ice control to OFF, ICE or CHILL. 4. (bottom right corner) This is used to turn the right side auger motor AUGER ON, AUGER OFF or AUGER REFILL ON. (Refill only applicable when installed) 5. (bottom right corner) This is used to turn the right side ice control to OFF, ICE or CHILL. 41084 102709 RECOMMENDED DAILY CLEANING (ULTRA-2 shown) NOTE – Turn the power OFF to the dispenser before proceeding. 1. Empty all product from the hopper(s). Disconnect the hopper lid lamp cord(s) and remove the lids. 2. Depress the hopper lock plunger. Lift the hopper up slightly. 3. Pull forward to remove. 4. Pull the auger from the cooling drum. 6. Caution: The faucet valve is under spring tension. Spread one side of the handle first, then the other and disconnect from the hopper. 7. Carefully slide the faucet valve up to remove the spring and faucet seal. Extra care should be taken when handling the seal to prevent damage. Do not fold the seal as this will cause damage to the Teflon® sealing surface. 5. Remove the cooling drum seal from the rear of the drum. 8. Remove the auger nose bushing from inside the hopper. 9. Care must be taken to ensure this surface does not get scratched during cleaning. Deep scratches could cause leakage around the seal. 10. Place all parts in a clean sink with mild hot water (120°F) and sanitizer solution. Allow all parts to soak for at least 5 minutes. Carefully wash all components with a clean wash cloth in the hot water and sanitizer solution. Use a clean, soft bristle brush as needed for the smaller components and tight areas. Do not immerse hopper lids. Use a commercial sanitizer th...