Assessments - , GPA: ( )

Instruções de Operação Bissell, Modelo LIFT-OFF 75Q3

Fabricante : Bissell
Arquivo Tamanho: 295.34 kb
Arquivo Nome : f9ac9e49-031f-4cfb-b1bf-2bb846d80b67.pdf

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

brush roll and brush roll belt maintenance the brush roll may accumulate debris such as strings, hair and fibers. this type of debris can wrap around the brush and diminish its ability to clean effectively. To remove brush roll for cleaning: 1. Turn power OFF (O). Remove foot 2. assembly from unit and turn over to access the brush roll. 2. Remove three Phillips head screws to remove the belt cover. 3. To remove brush roll, pull on the brush near the belt side. Clean off hair or other debris from brush roll. 4. Place cleaned brush roll back into foot 3 of unit by aligning the non-belt side so it's seated in the nozzle. 5. Pivot the brush roll so the belt end slides into the slot in the nozzle. 6. Replace the belt cover and secure with three screws. Attach foot assembly on unit. 800.237.7691 7 Maintenance and care Maintenance and care brush roll and brush roll belt maintenance continued Brush roll reset: if larger debris becomes lodged in the foot of the unit and the brush roll shuts off, turn the unit off and remove the obstruction. Wait approximately 15 seconds for the motor to cool down before turning back on. brush will function again after allowing time to cool down. Brush roll belt replacement: if the brush roll belt should break, call 1-800-237-7691 or visit WWW. bissell.coM to purchase replacement belt. Replacement instructions: 1. Turn power OFF (O). Remove foot assembly from unit and turn over to access the brush roll belt. 2. Remove three Phillips head screws to remove the belt cover. 3. Locate broken belt. 4. Replace belt. 5. Place brush roll back into foot of unit. 6. Replace the belt cover and secure with three screws. 7. Attach foot assembly on unit. disposal of batteries 2. 3. WaRning: This product contains Nickel Metal Hydride (NiMH) rechargeable batteries. According to Federal and Stateregulations, removal and proper disposal of NiMH batteries is required. For removal of the batteries in yourLift-Off Floor & More see instructions below. TM if your lift-off floors & More is to be disposed of, the batteries should be 3. removed and disposed of properly. 1. iMPoRtant: Unplug Charger. 2. Remove hand vac from unit and remove dirt cup from handle. 3. Remove (5) Phillips head screws on the 5 screws handle and cover. 8 800.237.7691 Maintenance and care Maintenance and care disposal of batteries continued 4. Separate left and right cover. 5. Remove the entire battery assembly from the cover. 6. Remove (3) Phillips head screws between the motor and battery bracket. 7. Pull the motor, PCB, fuse, and inner wire through the middle of the battery bracket, separating the battery bracket and single battery from the motor, PCB, and inner wire. 8. Cut wires from the PCB and fuse to the battery bracket. 9. Keep Battery Pack together – DO NOT separate individual batteries. For specific disposal instructions of batteries, please contact RBRC (Rechargeable Battery Recycling Corporation) 1-800-822-8837 or visit 10.Discard remainder of product caution: Disconnecting the battery will destroy the appliance and void the warranty. Troubleshooting Vacuum won’t turn on Possible causes Remedies 1. Battery isn’t fully charged 1. Charge battery. Follow charging battery instructions on page 5 brush roll not turning Possible causes Remedies 1. Brush roll is jammed 1. Remove obstruction. Follow instructions on pages 7 and 8 2. Brush roll needs to be reset 2. Follow instructions on page 8 3. Broken brush roll belt 3. Follow instructions on page 8 Vacuum cleaner has low suction Possible causes Remedies 1. Dirt container is full 1. Empty dirt container 2. Dirt container is not installed properly 2. Position container correctly and snap firmly into place 3. Foot is loose 3. Make sure foot is fully inserted into body of unit 4. Filters need cleaning 4. Follow filter instructions on page 7 5. Filters need replacing 5. Visit or call 1-800-237-7691 to order 9replacement filters. 800.237.7691 3 4 3 4 Troubleshooting Visible dirt escaping from vacuum Possible causes Remedies 1. Dirt container is full of debris 1. Empty dirt container 2. Filter is missing or installed incorrectly 2. Check filter for correct installation 3. Dirt container installed incorrectly 3. Position container correctly and snap firmly into place other maintenance or service not included in the manual should be performed by an authorized service representative. thank you for selecting a bissell product. Please do not return this product to the store. for any questions or concerns, bissell is happy to be of service. contact us directly at 1-800-237-7691. Replacement parts - BISSELL vacuum you may purchase parts by calling bissell consumer services or by visiting our website. below is a list of common replacement parts. Item Part No. Part Name 1 52H6 Filter assembly – set of 2 2 203-1612 Charging adapter plug 3 203-1609 Foot assembly 4 203-1610 Dirt cup assembly 5 203-1607 Brush roll belt 6 2...