Log:
Assessments - 4, GPA: 4 ( )

Instruções de Operação Hatco, Modelo FDW-1-MN

Fabricante : Hatco
Arquivo Tamanho: 814.14 kb
Arquivo Nome : 2134d398-deaf-4a90-8efe-342cc529281a.pdf
Língua de Ensino: en
Ir para baixar



Facilidade de uso


If the plug and receptacle do not match, contact a qualified electrician to determine the proper voltage and size and install the proper electrical outlet. WARNING To prevent any injury, discontinue use if power cord Figure 3. Plug Configurations NEMA 5-15P CEE 7/7 Schuko BS-1363 is frayed or worn. ELECTRICAL RATING CHART Model Voltage Hertz Watts Amps Plug Configuration Shipping Weight FDW-1-MN 100 120 60 60 1110 1128 11.1 9.4 NEMA 5-15P NEMA 5-15P 80 lbs. (36 kg) 80 lbs. (36 kg) 220 50/60 1118 5.1 CEE 7/7 Schuko 80 lbs. (36 kg) 240 220-230 (CE) 50/60 50/60 1128 1118-1222 4.7 5.1-5.3 BS-1363 CEE 7/7 Schuko 80 lbs. (36 kg) 80 lbs. (36 kg) 230-240 (CE) 50/60 1036-1128 4.5-5.7 BS-1363 80 lbs. (36 kg) FST-1-MN 120 220 60 50/60 1245 1225 10.4 5.6 NEMA 5-15P CEE 7/7 Schuko 132 lbs. (60 kg) 132 lbs. (60 kg) 240 50/60 1245 5.2 BS-1363 132 lbs. (60 kg) 220-230 (CE) 230-240 (CE) 50/60 50/60 1219-1332 1150-1252 5.6-5.8 5.0-5.2 CEE 7/7 Schuko BS-1363 132 lbs. (60 kg) 132 lbs. (60 kg) DIMENSIONS Width Depth Height Model (A) (B) (C) FDW-1-MN 18" 22-3/8" 27-1/2" (46 cm) (57 cm) (70 cm) FST-1-MN 22-7/8" 27" 32-5/8" (58 cm) (69 cm) (83 cm) A B C Figure 4. Dimensions 3 Form No. MNM-0702 INSTALLATION Form No. MNM-0702 4 Chip Deflector Floor Panels Decal-Install on upper stainless steel panel. Install chip deflector in slots located behind upper door panel. Figure 5. Set-Up (FDW-1-MN shown) SET-UP The Macho Nacho™ unit comes pre-assembled and ready for set-up. 1. Remove tape and protective film from all surfaces of unit. 2. Install the chip deflector inside, behind the upper door. See Figure 5. 3. Install decals on the upper front and side stainless steel panels. Before installing decals, clean the stainless steel side panels with a non-oily cleaner, such as isopropyl alcohol (rubbing alcohol). After the cleaned surfaces have dried, simply remove the protective backing from the decal and apply to the panel. Any air pockets or bubbles behind the decal can be removed by rubbing gently with a soft cloth, working from the center of the decal towards the outer edges. WARNING For safe and proper operation, the unit must be located at a reasonable distance from combustible walls and materials. If safe distances are not maintained, discoloration or combustion could occur. CAUTION To prevent injury or damage the unit must be transported in the upright position. If laid on its side, all glass surfaces must be secured with tape. CAUTION Locate the unit at the proper counter height, in an area that is convenient for use. The location should be level to prevent the unit or its contents from accidentally falling, and strong enough to support the weight of the unit and food displayed. CAUTION Unit is not weatherproof. For safe and proper operation locate the unit indoors where the ambient air temperature is a minimum of 70°F (21°C). OPERATION ALL MODELS CAUTION Some exterior surfaces on the unit will get hot. Use caution when touching these areas to avoid injury. 1. Plug warmer into a properly grounded electrical outlet of the correct voltage, size and plug configuration. See SPECIFICATIONS for details. 2. Turn the Power Switch to the ON position. See Figures 6 & 7. 3. Turn the Temperature Control to the desired temperature setting. 4. Allow unit 15-20 minutes to reach operating temperature. 5. Open top door and fill unit with chips. 6. At the end of the day or shift, turn unit off and allow to cool down. Clean as required. FLAV-R-FRESH Figure 6. Control Panel FDW-1-MN Temperature Control Power Switch Temperature Gauge FLAV-R-SAVOR Figure 7. Control Panel FST-1-MN Temperature Control Power Switch Temperature Gauge 5 Form No. MNM-0702 MAINTENANCE GENERAL Hatco Macho Nacho™ Chip Warmers are designed for maximum durability and performance, with minimum maintenance. WARNING To avoid any injury, turn the power switch off at the fuse disconnect switch/circuit breaker or unplug the unit from the power source and allow to cool completely before perfor...

Este manual também é adequado para os modelos :
Outros aparelhos de cozinha - FDW-1-MN (814.14 kb)
Outros aparelhos de cozinha - FDW-1-MN (814.14 kb)
Outros aparelhos de cozinha - FST-1-MN (814.14 kb)
Outros aparelhos de cozinha - FST-1-MN (814.14 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias