Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
/ (E30EW75GSS) 175 Lbs. • Single phase 3- or 4-wire cable, 120/240 or 120/208 Volt, 60 Hertz AC only electrical supply with ground required on separate circuit fused on both sides of line. • Connected Load (kW Rating) @ 240/208 Volts = 4.0/3.0kW • Amps @ 240/208 Volts =16.6/14.4 Amps • To support Wall Oven, two 3"-wide x 3/4"-thick planks must be installed as a base, capable of supporting 200 Lbs. Do NOT use full base, since planks are necessary to allow for proper air displacement. 30" Warmer Drawers Specifications • Product Weights – (E30WD75GPS/E30WD75GSS) 49 Lbs. / (E30WD75GTT) 41 Lbs. • Voltage Rating –120V/450W/60Hz/15 Amps • Connected Load (kW Rating) @120 Volts = 0.45kW (For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.) • Amps @120V = 3.75 Amps • Full base of solid plywood or similar material required, capable of supporting 100 Lbs. Note: For planning purposes only. Refer to Product Installation Guide on the web at electroluxicon.com for detailed instructions. Electrolux Major Appliances, N.A. High standards of quality at Electrolux Home Products, Inc. mean we are USA • 250 Bobby Jones Expressway • Augusta, GA 30907 • 1-877-4electrolux (1-877-435-3287) • electroluxicon.com constantly working to improve our products. We reserve the right to change CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • electroluxicon.ca specifications or discontinue models without notice. SO_EW_WD INST 01/09 © 2009 Electrolux Home Products, Inc. Printed in the U.S.A. 30" Combination Installation – Built-In Microwave /Single Wall Oven/Warmer Drawer 24"min. 3"max.†† 30"min. 97/8"min. 101/4"max. 13/4"min.† 26 1/2"min. 27"max. Full plywood base required to support 100 lbs. Full plywood base required to support 100 lbs. 281/2"min. 287/8"max. 28 1/2"min. 28 3/4"max. Two 3" wide by 3/4" thick planks must be installed, capable of supporting 200 lbs. 30" Warmer Drawer Cutout For models: E30WD75GPS E30WD75GSS E30WD75GTT 4"x 4" opening to route armoured cable 28 1/2"min. 28 3/4"max. 5" 11 1/2" 120V/60Hz grounded electrical outlet should NOT be located within shaded area 41/2"min. required 197/8"min. 203/8"max. 24"min.** (critical dimension) Electrical junction box location Bottom of oven cutout 11 5/8"min.** (critical dimension) For detailed product dimensions and installation specifications, refer to model-specific product page and installation guide on web * Minimum 31/8" clearance required from bottom of Built-In Microwave cutout to top edge of Wall Oven’s faceplate, leaving a 2"visible gap between both product faceplates ** Critical dimension – MUST be applied † Maximum height depends on critical dimension (115/8") †† Electrical junction box for Wall Oven must be lower than the Warmer Drawer cutout 2" (visible gap)* 30" Electric Single Wall Oven Cutout For models: E30EW75GPS E30EW75GSS 30" Built-In Microwave Cutout For model: E30MO65GSS 30" Combination Installation Specifications • Always consult local and/or national electric codes. (Refer to product-specific electrical specifications on this page.) • Minimum 24"deep cutout dimension is critical for proper combination installation, to ensure that each built-in product’s faceplate will fit flush against cabinet front. • Bases must be level and cabinet front must be square. • Minimum 4-1/2"required distance from bottom of Warmer Drawer cutout to floor. • Respect critical dimensions as noted for proper installation of built-In products. • Minimum 23-1/4" clearance needed for Wall Oven door depth when open. 30" Built-In Convection Microwave Specifications • Product Weight – 60 Lbs. • Voltage Rating –120V/ 60Hz/15 Amps • Connected Load (kW Rating) @120 Volts =1.55kW (For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.) • Amps @120 Volts =13 Amps • Consult local building code in the event that cutout opening may be required to be enclosed with sides, ceiling and rear partition. • Full base of solid plywood or similar material required, capable of supporting 100 Lbs. • Minimum 3-1/8"clearance required from bottom of Built-In Microwave cutout to top edge of Wall Oven’s faceplate, leaving a 2"visible gap between both product faceplates. 30" Electric Single Wall Ovens Specifications • Product Weights – (E30EW75GPS) 178 Lbs. / (E30EW75GSS) 175 Lbs. • Single phase 3- or 4-wire cable, 120/240 or 120/208 Volt, 60 Hertz AC only electrical supply with ground required on separate circuit fused on both sides of line. • Connected Load (kW Rating) @ 240/208 Volts = 4.0/3.0kW • Amps @ 240/208 Volts =16.6/14.4 Amps • To support Wall Oven, two 3"-wide x 3/4" thick planks must be installed as a base, capable of supporting 200 Lbs. Do NOT use full base, since planks are necessary to allow for proper air displacement. 30" Warmer Drawers Specifications • Product Weights – (E30WD75GPS/E30...