Assessments - 5, GPA: 4.8
(
)
)
|
Facilidade de uso
These warnings are provided in the interest of safety. You MUST read them carefully before installing or using the appliance. • To reduce the risk of injury, close supervision of children is necessary when the appliance is in use. • Do not put your fingers or hands into the waste disposer. • Turn the control switch to the ‘off’ position before attempting to clear a blockage or remove an object from the disposer. • When attempting to loosen a blockage in a waste disposer, use a long wooden object such as a wooden spoon or wooden handle of a broom or mop. • When attempting to remove an object from a waste disposer use long-handled tongs or pliers. • When not in use, leave the disposer cover in place to reduce the risk of objects falling into the disposer, you must ensure that the appliance is switched off. Contents General Features and Parts Specifications Installation Electrical Connections Helpful Hints Operation Cleaning and Maintenance Something Not Working? Service Customer Care Guarantee Conditions • To reduce the risk of injury by materials that may be rejected by a waste disposer, do no put the following into a disposer: a. Glass, china or plastic b. Large whole bones c. Metal, such as bottle tops, tin cans or aluminum foil d. Rubber items or string e. Wooden items f. Leather or cloth items g. Whole ‘corn on the cob’ h. Clam or oyster shells i. Drain cleaner • Do not operate the disposer unless the splash guard is in place. • See ‘Electrical Connections’ for the correct earthing of the appliance. Page 3 Page 3 Page 4 Page 6 Page 7 Page 7 Page 8 Page 8 Page 9 Page 9 Page 10 General Features and Parts STOPPER REMOVABLE SPLASH GUARD SINK FLANGE DIAMETER 33/8 X 12 THREADS/INCH RUBBER SINK FLANGE GASKET FIBER GASKET SUPPORT RING NOTE ARROWS INDICATING UP MOUNT RING TIGHTENING EARS CUSHION MOUNT DISHWASHER DISCHARGE INLET ELBOW GASKET SCREWS ELBOW FLANGEEND BELL (ELECTRICAL CONNECTIONS) Z GROOVE G HOPPER DISHCHARGE ELBOW Y SINK Specifications Dimensions Electrical specifications are on the disposer rating label. “B” “C” “A” “E” “D” 11/2” (38mm) BPS MODEL “A” “B” “C” “D” “E” WDU4100 Inches 141/16 615/16 53 /16 51/16 23/4 mm 357 176 132 129 70 WDU4400 Inches 151/8 71/4 85/8 59/16 23/4 mm 384 184 219 141 70 Some Typical Installations SINGLE BOWL DOUBLE BOWL / CENTRE OUTLET DOUBLE BOWL / END OUTLET 10” (254 mm) 10” (254 mm) 10” (254 mm) APPROX. APPROX. APPROX. Installing the waste disposer When INSTALLING the disposer, refer to the EXPLODED VIEW on page 3. The installation of this appliance should be carried out by a competent or qualified plumber. Before installing a new disposer, inspect waste pipe. Ensure the drain is clear of obstruction before use. If the dishwasher drain pipe is to be connected to the disposer, it will be necessary to remove the knock out plug from the dishwasher discharge inlet on the disposer. The plug can be knocked out using a hammer and chisel or screwdriver. The knock out plug will fall into the disposer, please ensure that this is removed before the installation of the disposer. KNOCK OUT PLUG Fig. A Installation The disposer is supplied with two sink gaskets. A. The thin gasket assembled with the sink flange is for use instead of putty with stainless steel sinks and most pressed steel sinks. B. The thick gasket included in the carton is for use instead of putty with cast iron sinks and some deep well pressed steel sinks. If for any reason you do use plumbers putty, follow this procedure: Form a ring of putty around the underside of the sink flange. Insert the sink flange into sink opening, press down firmly on sink flange to squeeze out any excess putty. Then, from underneath the sink, use a knife to trim off excess putty flush with bottom edge of the sink opening. If you use putty, do NOT use gasket(s). When positioning the disposer ensure that the red reset button is easily accessible after completion of the installation. The disposer is equipped with an easy to use mounting system. The disposer mounting comes completely assembled, so it will be necessary to disassemble the mounting parts before continuing with the installation. Carefully observe how the mounting parts disassemble, as this will make re-installation simple and understandable. Turn the mount ring clockwise to remove it from the disposer hopper. The mount ring is shipped in the ‘support’ position. Raise the mount ring upward toward the top of the sink flange, exposing cushion mount. Remove cushion mount from the sink flange. The mount ring can now be removed. Unscrew the support ring from the sink flange. When using a gasket: Insert the sink flange through the sink gasket into sink opening. Do not rotate the sink flange, once it is seated. From underneath the sink, place the fibre gasket over the sink flange and screw the support ring on to the sink flange. Note There are arrows indicating the correct side to face upward. Do not overtighten, the sink flange will not move when tightened securely. Slip the mount ring...
Este manual também é adequado para os modelos :Outros aparelhos de cozinha - WDU4400 (187.32 kb)