Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
13. Remove icemaker top panel and Fig. 8 louvered side panel. 14. Insert ice transport tube to a 1/2" (13mm) depth through mounting bracket (Fig 8 and 9.1) and secure transport tube away from condenser fan under float reservoir bracket (Fig. 9.2). 15. Tighten clamp screw(s) on icemaker base securely (Fig. 9.3). 16. Uncoil capillary tube from bin thermostat and route through hole in gasket to mounting bracket and secure as shown (Fig. 8). 17. Reinstall icemaker louvered side panel and top panel. GO TO STARTUP – STEP 27. ice transport tube bin thermostat capillary tube 1/2" 2" Fig. 9 2 1 insert ice transport tube tighten 3 clamp screw 10 Satellite-fill icemaker installation Fig. 10 – Single ice tube dispensers 18. Ice transport tube chase may be located behind or to either side of the dispenser (Fig. 10 and 11). Using the chase mounting bracket (Fig. 12) as a template mark the counter for the ice transport tube(s) in one of the locations shown in Fig. 10 and 11. Within the template outline drill one 2.25" (58mm) to 2.375" (61mm) hole for each ice transport tube. Secure the chase mounting bracket to the counter using supplied screws (Fig. 12). 2.25" (57mm) - 2.375" (61mm) dia. hole typical 1.25 (32mm) 1.25" (32mm) 1.25" (32mm) 3" (77mm)3" (77mm) front side entrychaseside entrychase rear entry chase A B 6" (153mm) Dime AnsionDime B nsionSingle tube – Fig. 10 22" (559mm) dispenser 11.00" (280mm) 8.00" (242mm) 24" (607mm) dispenser 12.00" (312mm) 9.00" (299mm) 30" (762mm) dispenser 15.00" (762mm) 12.00" (343mm) Double tube – Fig. 11 22" (559mm) dispenser 9.50" (242mm) 8.00" (204mm) 24" (607mm) dispenser 10.50" (273mm) 9.00" (242mm) 30" (762mm) dispenser 13.50" (343mm) 12.00" (305mm) 44" (1118mm) dispenser 20.50" (521mm) 19.00" (483mm) Fig. 11 – Double ice tube dispensers 2.25" (57mm) - 2.375" (61mm) dia. hole typical 1.25 (32mm) 1.25" (32mm) 1.25" (32mm) 1.50" (38mm) 1.50" (38mm) front side entrychaseside entrychase rear entry chase 4.50" (115mm)4.50" (115mm)A B 6" (153mm) Fig. 12 11 21. Route the bin signal cord from the 4" x 4" (102mm x 102mm) junction box through the top knockout (Fig. 13.1) and countertop hole. Attach the bin signal connector to the two lead plug on the icemaker. 22. Route the ice transport tube(s) from the icemaker(s) through counter cutout and knock out into dispenser top by following the same routing as the bin signal cord (Fig. 13.2). 19. Remove lid from dispenser top (Fig. 13.). Remove the knockout from the Harmony top (Fig. 13.2) corresponding to selected chase location. Line the edges of the opening with the supplied gasket material (Fig. 13.2). 20. Follow the “Satellite-fill icemaker installation procedure” found in the Symphony MCD400 Icemaker Manual 208600 to install your Follett icemaker. 12 1 1 2 2 2 1 Fig. 13 23. Connect the ice transport tube(s) to the dispenser: a) Drill 3/16" (5mm) holes through both sides of the tube 1/2" (13mm) from the tube end. b) Collapse tube and insert through gasketed hole (Fig. 14.1). c) Match tube holes to bracket tabs. 24. Route bin thermostat capillary tube from the 4" x 4" (102mm x 102mm) junction box into bin alongside the ice transport tube. Secure capillary tube into bracket (Fig. 8). 25. Reinstall the dispenser cover with supplied screws (Fig. 14). 26. Install telescoping chase. a) Mount lower chase section to chase bracket on counter with supplied screws (Fig. 15.1). b) Position upper chase section over lower chase section. Align top of upper section to top of stainless dispenser top and secure with screw (Fig. 15.2). c) Drill pilot holes on both sides of chase and secure with supplied screws (Fig. 15.3). 27. Turn icemaker power and water on. 28. After icemaker has made ice for approximately 15 minutes complete the following start-up checks: a) Dispense ice. b) Hold ice on bin thermostat and make sure icemaker shuts off. c) Remove ice from bin thermostat and make sure icemaker restarts. Note: Icemaker has a 20 minute restart delay. Fig. 15 13 2 3 1 Fig. 14 1 Operation Weekly exterior evaporator unit care The exterior may be cleaned with a stainless cleaner such as 3M Stainless Steel Cleaner & Polish or equivalent. Recommended semi-annual icemaker/evaporator unit cleaning (every 6 months) Fig. 16 Solution A – Sanitizing solution: Prepare 2 gallons (9L) Combine 1 oz (250ml) bleach with 2 gal (8L) hot water or use 200ppm of Ecolab Mikro-chlor Cleaner or equivalent 5.25% sodium hypochlorite solution. Solution B – Ice machine cleaner: Prepare one gallon (3.8L) of Follett SafeCLEAN™ Ice Machine Cleaner (one 7 oz packet) or equivalent. Solution temperature must be at least 120° F (48.9° C). Warning: Most ice machine cleaners contain citric or phosphoric acid that can cause skin irritation. Read caution label on product and follow instructions carefully. Fig. 17 1. Remove icemaker panels required to gain access to water reservoir components (Fig. 16) and electrical control box. 2. Locate icemaker electrical box and turn compressor switch off. 3. Disp...