Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
After the time delay the machine will restart and the TIME DELAY, HI AMP, and SERVICE LED’s will clear. LO WATER: During operation, the water level cycles between the normal low and normal high sensors. Should the water be shut off to a running machine, a soft error will occur. The error sequence is as follows: During operation, the water level falls to the normal low sensor, and when it does the water feed solenoid is energized. If water is not detected at the normal low sensor within 120 seconds, a soft error will occur. The machine will shut down, but the water feed solenoid will remain energized. Should water return, it will fill to the normal low sensor and the machine will resume normal operation. The error will clear automatically. DRAIN CLOG: The drain clog sensor, located in the plastic drain pan behind the drain solenoid, will detect the presence of water just below the top edge of the pan. If water does not properly flow out of the drain pan it will rise to the sensor, especially during a self-flushing purge cycle. Hard error: HI AMPS: 1. “Two strikes” feature. If the gearmotor has a second HI AMP occurrence during the countdown period (6 hours after a HI AMP time delay) a hard error will occur and the HI AMP and SERVICE LED’s will be illuminated. 2. No current. To prevent the refrigeration system from running without gearmotor rotation the PC board will indicate HIGH AMP and SERVICE if the drive relay is energized and there is no current draw. HI PRESSURE: Should the refrigeration pressure rise above 425 psi, a hard error will occur. Even if pressure fall-back below the reset point of 295 psi, the error will not clear and the machine will not restart. LO WATER: 1. There is a sensor in the water reservoir that reaches down to the very bottom. The machine will not start if water is not present at this sensor. 2. A hard error will occur should water not be present within 60 seconds of power up or if the sensors are disconnected or damaged. Relay output indication: Each relay on the board has an indicator light associated with its output. For example, when the relay for the water feed solenoid is energized, the adjacent indicator light glows green. Comp/Sol output: The output for the compressor is labeled COMP/SOL. 15 801 CHURCH LANEEASTON, PA 18040, USA800-523-9361 OR 610-252-7301FOR SERVICE CALL: ON THE WEB: LELE 2LOWNORM 6HIGHNORM LE3COM LE4ALARM LE LOW 7LE 8CLOGDRAINCOM WATER LEVELOUT (light on) -V (3 WIRE) +V RETURN(CONTACT CLOSURE) BINFULL S3CLEAN MOM S2PURGE MAINT OR INPUT 2 1234 J51RED / GRAY PAIRGRAY / GRAY PAIR J24 J22J23 CONTROL PC BOARD J21 JUMPER PURGE (Y) POWER (G) LOW BIN (G) AUGER ON (G) REFRIG ON (G) CLEANING (Y) SERVICE (R) HI AMPS (R) HI PRESS (R) LO PRESS (R) DRAIN CLOG (R) TIME DELAY (Y) LO WATER (R) CPU (G) HI WATER (R) SWITCHRESET 1y/230Vac SIGNALRETURN2 J3 GRAY / GRAY PAIR HIPRESSHIGH PRESSUREOPENS @ EXCESSP 2PE OPEN @ 425 PSICLOSE @ 295 PSI K1CNO L1 J7J4J5 MOTORFAN J17 J18 J2 BRNBLU 123 J50 .6 Amp Max1/2hp Max NOCK3 J6 M2M1 #2 #12 #1#3 GRN #34 CB1 COMPSOLFANDRV #19#18SNUBBER 20FLA240VacCONTACTORL2 25 #7#8 S1O I240Vac / 20FLAOFF/ON14 ~12 Amp DRAW RUNNING50/60Hz208V/230Vac #47 #39 #40 #41 #42 #43 #45#46#44 P1 K11 C2 START C1 RUN COMP SRC 6 41 25 J10J9 L2 J11J12J8 #11 #31#30#33#32 FCV-1 FCV-2 230Vac20Watt 20Watt230VacDRAIN INPUTWATER J16 J13 J14 J15 H2OIN POTENTIALRELAY H2ODRN TP11TP4 TP7 TP8 TP6TP5TP3 BLUBRNGRN AMPSENSINGD9D5D10 D6 D15 BLUBLKBRN P52 L2GNDL1 #38#37 #37#38#2BLUBRN L1 J52 J34J33J32J31 1111 1 Wiring diagram LELE 2LOWNORM 6HIGHNORM LE3COM LE4ALARM LE LOW 7LE 8CLOGDRAINCOM WATER LEVELOUT (light on) -V (3 WIRE) +V RETURN(CONTACT CLOSURE) BINFULL S3CLEAN MOM S2PURGE MAINT OR INPUT 2 1234 J51RED / GRAY PAIRGRAY / GRAY PAIR J24 J22J23 CONTROL PC BOARD J21 JUMPER PURGE (Y) POWER (G) LOW BIN (G) AUGER ON (G) REFRIG ON (G) CLEANING (Y) SERVICE (R) HI AMPS (R) HI PRESS (R) LO PRESS (R) DRAIN CLOG (R) TIME DELAY (Y) LO WATER (R) CPU (G) HI WATER (R) SWITCHRESET 1y/230Vac SIGNALRETURN2 J3 GRAY / GRAY PAIR HIPRESSHIGH PRESSUREOPENS @ EXCESSP 2PE OPEN @ 425 PSICLOSE @ 295 PSI K1CNO L1 J7J4J5 MOTORFAN J17 J18 J2 BRNBLU 123 J50 .6 Amp Max1/2hp Max NOCK3 J6 M2M1 #2 #12 #1#3 GRN #34 CB1 COMPSOLFANDRV #19#18SNUBBER 20FLA240VacCONTACTORL2 25 #7#8 S1O I240Vac / 20FLAOFF/ON14 ~12 Amp DRAW RUNNING50/60Hz208V/230Vac #47 #39 #40 #41 #42 #43 #45#46#44 P1 K11 C2 START C1 RUN COMP SRC 6 41 25 J10J9 L2 J11J12J8 #11 #31#30#33#32 FCV-1 FCV-2 230Vac20Watt 20Watt230VacDRAIN INPUTWATER J16 J13 J14 J15 H2OIN POTENTIALRELAY H2ODRN TP11TP4 TP7 TP8 TP6TP5TP3 BLUBRNGRN AMPSENSINGD9D5D10 D6 D15 BLUBLKBRN P52 L2GNDL1 #38#37 #37#38#2BLUBRN L1 J52 J34J33J32J31 1111 1 Wiring diagram 16 Compressor data Compressor current draw Air-cooled Ambient air temp. 60°F/16°C 6.9A Water-cooled Condenser water temp 50°F/10°C 70°F/21°C 6.9A 60°F/16°C 80°F/27°C 7.0A 70°F/21°C 90°F/32°C 7.3A 80°F/27°C 100°F/38°C 7.9A 90°F/32°C 7.4A 7.4A 7.4A 7.5A 7.5A Locked rotor amps 96.8 Gearmotor data Brother Gearmoto...
Este manual também é adequado para os modelos :Outros aparelhos de cozinha - HCE1400W (3.3 mb)