Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
3-6 Guide de l’installation ................................................................. 6 Guia de la Instalacion ............................................................... 12 TABLE OF CONTENTS Form No. B/03/03 Part No. 8101P549-60 © 2003 Maytag Appliances Sales Co. Litho U.S.A . BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT: • Save these instructions for the local electrical inspector’s use. • OBSERVE ALL GOVERNING CODES AND ORDINANCES. NOTES: TO INSTALLER: • Leave these instructions with the appliance after installation is completed. TO CONSUMER: • Keep the User Guide and Installation Instructions for future use. • This appliance must be properly grounded. • Insure that the power cord does not contact the hot surfaces on the bottom of ovens, cooktops, or any other appliance. PRODUCT DIMENSIONS Including handle TOOLS & MATERIALS NEEDED • 2" x 4" or 2" x 2" lumber for runners and brace • Wood screws and adhesive or other hardware for installing runners or shelf to support warmer drawer • Runners must be level, rigidly mounted and capable of supporting 150 pounds. • Saw • Level • Drill and 1/16" bit • Phillips screwdriver PLANNING The warming drawer may be installed directly into a wall or wall oven cabinetry. The warming drawer may be installed below a countertop, a single, combo or double oven or side by side using 2 drawers. When installing the warming drawer with a cooktop allow a 2" minimum from bottom of a cooktop burner box to top of cutout. A 2" minimum clearance between oven and warming drawer cutouts is required. 30" 10 1/2" 23 1/4"27 7/16" ProStyle Front25 1/4" Curved Front 9" 27 7/16" ProStyle Front25 1/4" Curved Front The electrical power cord is located on the right side of the warming drawer. Locate the outlet within reach of the 56" long power cord in adjacent cabinet, within 42" of the right side or 16" from the left side of the cutout. A recessed receptacle can be installed on the right side of the cutout, 7" maximum from the back of the cabinet. REMOVE PACKAGING AND PARTS Parts provided: 4 Wood screws UNPACKING 1.Place carton on a flat surface. 2.Open the top of the carton and lift off the cardboard spacer. 3.Lift the warming drawer up and out of the carton. 4.Place the drawer on top of the cardboard to protect the drawer and the finished flooring. 5.Remove all packing materials and tape. 6.Locate package containing 4 wood screws and set aside. 1 GROUNDING THE APPLIANCE IMPORTANT (Please read carefully) FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED. Do not use an extension cord or adapter plug with this appliance. Follow National Electrical codes and ordinances. This warming drawer must be supplied with 120V, 60Hz, and connected to an individual, properly grounded branch circuit, and protected by a 15 or 20 amp circuit breaker or time delay fuse. •A properly grounded 3-prong receptacle should be located within reach of the drawer’s 56” long power cord. • Locate the receptacle in an adjacent cabinet. –Within 42” of the right side or, –Within 16” of the left side or, –A recessed receptacle may be located on the right side of the cutout, 7” maximum from the back of the cabinet. In this location, the excess power cord should be coiled to the right side of the unit using the cord clip provided. Recessed receptacle 7" max. from rear on right side Drill 11/2" hole for power cord for left or right side outlet location IMPORTANT (Please read carefully) The power cord of this appliance is equipped with a 3-prong (grounding) plug that mates with standard 3-prong grounding wall receptacle to minimize the possibility of electric shock. The customer should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded and has the correct polarity. • Where a standard 2-prong wall receptacle is encountered, it is the personal responsibility and obligation of the customer to have it replaced with a properly grounded 3prong wall receptacle. Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. DO NOT USE AN EXTENSION CORD. 2 SPECIFICATIONS AND REQUIREMENTS WHEN INSTALLING BELOW A COUNTERTOP Drawer overlaps will conceal cut edges on all sides of the opening. The rough opening for the drawer must be: • Depth: 23-1/2" minimum from inside back to front of cabinet frame. • Width: 28-1/2" • Height: 9-1/4" 5" minimum above floor or 1" above toe kick. 23-1/4" from floor to bottom of cutout is recommended for under countertop installation. NOTE: If you are installing in frameless cabinets, it may be necessary to install 1/2" wide cleats to accept drawer mounting screws. See drawer to find exact locations of mounting screws. WHEN INSTALLING BELOW A COOKTOP Warming drawers are suitable for installation below only certain specified cooktop models. See the label attached to the top of the warming drawer for suitable models. 281/2" *NOTE: When installing warming drawer ...