Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SECTION II. ALTERNATE REPAIR INSTRUCTIONS, BEFORE 1998. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 WARNING Before installing this product, read and follow all warning notices and instructions accompanying this product. Failure to follow safety warnings and instructions can result in severe injury, death, or property damage. Call (800) 831-7133 for additional free copies of these instructions. Important Notice Attention Installer. This manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner/operator of this equipment. DANGER Risk of Electrical Shock or Electrocution. Always disconnect power to the pool light at the circuit breaker before servicing the light. Failure to do so could result in death or serious injury to installer, serviceman, pool users or others due to electrical shock. WARNING Never operate this underwater light for more than 10 seconds unless it is totally submerged in water. Without total submersion, the light assembly will get extremely hot, which may result in serious burns or in breakage of the lamp or lens. This may result in serious injury to pool users, installers, or bystanders, or in damage to property. WARNING Use only the special pilot screw provided with this underwater light. This screw mounts and electrically grounds the housing securely to the mounting ring and wet fixture housing. Failure to use the screw provided could create an electrical hazard which could result in death or serious injury to pool users, installers or others due to electrical shock. This procedure can be performed with the water in the pool. Pentair Water Pool and Spa™ 1620 Hawkins Ave., Sanford, NC 27330 • (919) 556-8000 10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 553-5000 Rev. A 1-18-06 1 P/N 620001 SECTION I. FIXTURE HOUSING ENTRY HUB REPAIR INSTRUCTIONS. STEP 1 Before starting repair, ensure that the inside of the fixture housing has the same style entry hub as shown in Figure 1. It is necessary to verify the correct style entry hub for this warranty repair. The hub may be at the top on the large radius of the fixture housing (45 degree entry), or assembled to the small fixture housing. Before continuing, ensure the conduit entry hub matches Figure 1. Do not attempt the repair on any fixture housing with any other style entry hub. Even if another type fixture housing shows the same staining, it is likely to be caused by another problem. In that case this procedure will not work and the repair will not be covered by warranty. Three posts on a ring with the hub lip formed over the edge of the ring I.D. Figure 1. P/N 620001 2 Rev. A 1-18-06 Fixture Housing Entry Hub Repair Instructions. STEP 2 1. If there is no internal bond wire as shown, skip to STEP 3. 2. If there is an internal bond wire or a non-listed potting material around the bond post, remove the potting material completely. A non-listed potting material would be silicone, RTV, etc. a. Be very careful not to damage the No. 8 bond wire, the screw or the post. 3. Replace the bond wire or the bonding screw if it is damaged. Then go to instruction STEP 4 and complete the procedures through STEP 6. Light Fixture Cord Internal Bond Wire Remove bonding lug potting material if present, check that screw is tight. Fixture 2. Rev. A 1-18-06 3 P/N 620001 Fixture Housing Entry Hub Repair Instructions. STEP 3 If there is no internal bond wire in the conduit, the fixture housing will appear as shown in Figure 3. No bond wire in conduit unused bond screw. Figure 3. P/N 620001 4 Rev. A 1-18-06 Fixture Housing Entry Hub Repair Instructions. STEP 4 WARNING Working with muriatic acid can be dangerous. When cleaning elements always wear rubber gloves and eye protection. Add acid to water, do not add water to acid. Splashing or spilling acid can cause severe personal injury and/or property damage. 1. Completely clean the fixture housing, the light fixture and the pool wall of all of the brown/black staining. The stain can be removed by brushing the stained area with a stainles steel pool brush. a. For stubborn stains, treat the stained area with a mild solution of muriatic acid and water (1:5 ratio). 2. Remove any excess plaster that may be around the entry hub area of the fixture housing. Remove all staining from the entry hub, fixture housing, and light fixture. Figure 4. Rev. A 1-18-06 5 P/N 620001 Fixture Housing Entry Hub Repair Instructions. STEP 5. 1. Attach an anode block, (with an allen head set screw), installed directly to one of the two unused posts on the hub ring. a. This is done by pushing the center hole of the block firmly and completely over the post, press-fitting it into place. 2. Position the anode to clear the fixture cord with its rounded edge pointed away from the center of the conduit entry, see Figure 5. Figure 5. P/N 620001 6 Rev. A 1-18-06 Fixture Housin...