Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
5. Slide other end of adjusting plate/shim in slot on mitered edge of side perimeter trim (see Figure 13). 6. While firmly holding edges of perimeter trim together, tighten both set screws on the adjusting plate with slotted screwdriver. 7. Repeat steps 1 through 6 for other corner. 8. Set perimeter trim assembly aside for later installation. Figure 13 - Assembling Brass Trim Side Brass Trim Top Brass Trim Mitered Edge Shim Set Screws Adjusting Plate Slot INSTALLING OPTIONAL BLOWER ACCESSORY GA3450TA Removing Upper Louver To install the blower accessory, you must first remove the upper louver. 1. Lift screen off fireplace and remove log set if installed. 2. Remove 4 screws from upper louver (see Figure 11, page 10). Save these screws. 3. Pull upper louver straight out from the cabinet. Be careful not to scratch the paint. Set louver aside. 4. Open lower louver door by swinging door down (see Figure 11, page 10). INSTALLATION Optional Mantel Installation (Cont.) Installing Optioanl Blower Accessory GA3450TA 111244-01A Forr morre iinfforrmattiion,, viisiitt 12 3 2 1 OFFPILOT ON HI LO Installing Blower Accessory Note: If you are using a mantel with your fireplace, use the following instructions. If your fireplace is built-in, see For Built-In Installation, page 13. 1. Install snap bushings found in blower kit into hole in left side of outer casing and into one of the holes in rear of remote/ blower bracket. 2. Make sure the wire harness is firmly connected to the terminals on the blower bracket assembly. 3. Note the wire locations on back of AUTO/OFF/ON switch. The terminals on back of switch are numbered 1, 2, and 3. Carefully remove red wire from terminal 3 and blue wire from terminal 1. Black wire can remain on middle terminal 2 (see Figure 14). 4. Carefully disconnect green and white wires at their insulated connectors (see Figure 15). Figure 14 - Installing Blower Bracket Assembly (Remote-Ready Unit Shown) CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. CAUTION: Verify proper operation after servicing. Wire Harness Blower Bracket Assembly Screw Wire Harness Switch Baffle Wiring Routing Hole in Baffle Switch Plate Blue Red Remote/Blower Bracket Power Cord INSTALLATION Continued Figure 16 - Installing Switch Plate to Remote/Blower Bracket Figure 15 - Wiring Diagram For Blower Accessory Standard Installation Red Red Fan Switch (Auto/Off/On) Blue Blue Thermostat Switch (N.O.) Green White Green White On 110/115 V.A.C. Blower Motor Black Off 1 2 3 Auto 5. In top of the fireplace cabinet, locate the four mounting holes on the outer casing. Align these four holes with those on the blower bracket assembly. Attach blower bracket assembly to the outer casing with 4 #10 screws provided (see Figure 14). 6. Route the wire harness through the hole in left side of baffle and between firebox wrapper and outer casing. 7. Insert the 4 wire harnesses from behind the remote/blower bracket through hole in rear of bracket with bushing and through the left rectangular hole to front of fireplace (see Figure 14). 8. Reconnect red wire to switch position 3. Reconnect blue wire to switch position 1. Reconnect green and white wires. 9. Install the switch plate on the remote/blower bracket with 2 #10 screws provided (see Figure 16). Route power cord out of the cabinet by inserting it through the bushing on the outer casing (see Figure 14). Plug fan kit into 120-Volt grounded power supply and test operation. Note: When switch is in the AUTO position, the fan will start after the fireplace has run for a few moments. The fan will continue to run for several moments after the fireplace has been turned off. When switch is in the ON position, the fan will run until turned to OFF. 10. Reinstall upper louver beginning with bottom screws (see Figure 11, page 10). Close lower louver door. Remote/Blower Bracket Switch Plate Screw Black Blower Mounting Holes Lower Louver Door INSTALLATION Installing Optional Blower Accessory GA3450TA (Cont.) 111244-01A Forr morre iinfforrmattiion,, viisiitt 1133 3 2 1 OFFPILOTON HI LO Red Red Fan Switch (Auto/Off/On) Blue Blue Thermostat Switch (N.O.) Green White Green White On 110/115 V.A.C. Blower Motor Black Off 1 2 3 Auto Figure 17 - Installing Blower Bracket Assembly Figure 18 - Wiring Diagram For Blower Accessory Built-In Installation INSTALLATION Continued INSTALLATION Installing Blower Accessory GA3450TA (Cont.) For Built-In Installation WARNING: A licensed electrician must connect the wiring harness to electrical supply following all local codes. Electrician must provide a clamp on the box cover to secure the wiring. Wiring should be routed through the bushing in the hole on the outer casing of fireplace. 1. Install snap bushing from blower kit into one hole on rear of remote/ blower bracket (see Figure 17). The other hole is for a strain relief clamp (not supplied) to secure incomin...