Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Models CD32M sereies, CD36M-A series and CD42M-A are heat circulating gravity direct-vent fireplaces with sealed combustion chamber. These fireplaces use millivolt gas control valve and millivolt ignition system. These fireplaces are convertible with the standard setup as natural gas. Conversion may be performed by the O.E.M. mobile home builder or by a qualified service person on-site. If you are uncertain as to what gas your unit is equipped for, please check the rating plate located inside of the appliance opening or consult your mobile home supplier or your local distributor of DESA/Coleman products. NOTICE: Check local building codes for area requirements before installing this appliance. BEFORE YOU BEGIN Before beginning the installation of your appliance, read these instructions through completely. This DESA/Coleman fireplace and its components are safe when installed according to this installation manual and operated as recommended. Unless you use DESA/Coleman components designed and tested for this fireplace system, YOU MAY CAUSE A SAFETY HAZARD! The DESA/Coleman warranty will be voided by, and DESA/ Coleman disclaims any responsibility for the following actions: A) Modification to the fireplace, components, doors, blower, fans or vent system. B) Use of any component part not manufactured or approved by DESA/Coleman in combination with a DESA/Coleman fire place system. Proper installation is the most important step in ensuring safe and continuous operation of the fireplace. Consult the local building codes as to the particular requirements concerned with the installation of all factory built fireplaces. This fireplace, when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/ NFPA 70 or the Canadian Electrical Code, CSA C22.1. The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 or the Canadian Installation Code, CAN/CGA B149. This appliance complies with ANSI Z21.88-1998 and CSA 2.33-M98 as a VENTED GAS FIREPLACE HEATER. For more information, visit more information, visit 111916-01A SELECTING LOCATION PRE-INSTALLATION PREPARATION Clearances to Combustibles Mantel Clearances 3 SELECTING LOCATION To determine the safest and most efficient location for your fireplace, consider the following guidelines: 1. The location must allow for proper clearances (see Figure 1). 2. Consider a location where the firepace would not be affected by drafts, air conditioning ducts, windows or doors. 3. A location that avoids the cutting of joists or roof rafters makes ventilation installation easier. In selecting a location, the following precautions must be observed: • Do not connect this appliance to a chimney system used for solid fuel burning fireplace. • Due to high temperatures, do not locate this appliance in high traffic areas or near furniture and draperies. • Never obstruct the openings of the appliance or flow of ventilation air. Keep the control compartments accessible. • Do not locate appliance close to where gasoline or other flammable liquids may be stored. The appliance must be kept clear and free from combustible materials. • Do not use this appliance if any part has been under water. Immediately contact a local service technician to examine the appliance and to replace any part(s) of the control ignition system and other related components that have been submerged under water. FULL PROJECTION CORNER INSTALLATION FLUSH INSTALLATION Figure 1 - Common Fireplace Locations Flush installation is recommended where living space is limited. Projected installation may be ideal for a new addition to an existing finished wall. Corner installation makes use of a space that may not normally be used and provides a wider and more efficient range for radiant heat transfer. PRE-INSTALLATION PREPARATION CAUTION: Do not block required air spaces with insulation or any other material. Do not obstruct the effective opening of the appliance with any type of facing material. CLEARANCES TO COMBUSTIBLES Minimum clearances to combustibles for the fireplace are: • Back and Sides of Fireplace .................................................. 0" • Floor ...................................................................................... 0" • Perpendicular Wall ................................................................ 6" • Front .................................................................................... 36" • Top of Standoffs .................................................................... 0" MANTEL CLEARANCES Woodwork, such as wood trims, mantles, and other combustible materials should be placed within the required clearance specified in Figure 2. Figure 2 - Mantel Clearances C B A D E F G Top of Louver Opening 3 2 1 4 5 6 7 Wall Mantel Mantel From Top Depth of Opening (1) 14" (A) 16" (2) 12" (B) 14" (3) 1...
Este manual também é adequado para os modelos :Outros acessórios para a casa - CD36M (3.3 mb)
Outros acessórios para a casa - CD42M-A (3.3 mb)