Assessments - 4, GPA: 3
(
)
)
|
Facilidade de uso
Keep assembly area clean and well 3. lit. Keep bystanders out of the area dur4. ing assembly. Do not assemble when tired or when 5. under the influence of drugs or medication. Use Precautions Do not operate any fuel burning 1. device inside the greenhouse. Asphyxiation hazard! Do not smoke or allow sources 2. of ignition inside the greenhouse. Risk of fire! Greenhouse is not flame retardant. Snow/debris accumulation hazard. 3. The heavy weight of accumulated snow or other debris can cause parts of this greenhouse to buckle suddenly. Do not allow snow or debris to accumulate on top of the greenhouse. NEVER enter a greenhouse with accumulated debris on top. Assemble the Greenhouse in a 4. smooth, level area that is sheltered from the wind. High winds can tear the Greenhouse 5. loose from the Spikes and could result in property damage or personal injury. In case of severe weather or high winds, take the Greenhouse apart or move it under cover. This product is not a toy. Do not al6. low children to play with or near this item. Use for intended purpose(s) only.7. Inspect before use; do not use if parts 8. loose or damaged. Maintain product labels and name9. plates. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. The warnings, precautions, and in10. structions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Save these instructions. Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Assembly Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Note: The Greenhouse is heavy and unwieldy when fully assembled. It should be assembled near the area where it will be anchored. The area should be firm, level, and provide shelter from the wind. Figure for Slat Assembly (Steps 1-3) 1. Slide two Rafter Slats (O) into the sleeves on the top of the Front Panel (K). Slide two Side Slats (P) into the 2. sleeves on the sides of the Front Panel. Slide Bottom Slat (Q) into the sleeve 3. on the bottom of the Front Panel. Figure for Pole Assembly (Steps 4-6) 4. Fit the covered Rafter Slats into the grooves in the Rafter Poles (G) and slide into place, with the holes on the Rafter Poles facing toward you (see insets above). Fit the covered Side Slats into the 5. grooves in the Side Poles (H) and slide into place, with the holes on the Side Poles facing toward you. Fit the covered Bottom Slat into the 6. groove in the Bottom Pole (F) and slide into place, with the holes on the Bottom Pole facing toward you. Figure for Connector Ass’y (Steps 7-8) 7. Secure the Rafter Poles together at the peak of the roof using Connector A. Make sure the unconnected point on the Connector faces towards you. Secure both top corners using a 8. Connector B on the left side and a Connector C on the right side, again make sure the unconnected point on the Connectors face towards you. Secure the bottom left-hand corner 9. of the Panel with Connector D. Use the Hex Wrench (T) to fasten a Hex Screw (S) into the hole on the bottom of the Bottom Pole. Secure the bottom right-hand corner 10. of the Panel with Connector E. Use the Hex Wrench (T) to fasten a Hex Screw (S) into the hole on the bottom of the Bottom Pole. Repeat the above steps to assemble 11. the Rear Panel (L). Figure for Panel Assembly (Step 12) 12. Line up the Connectors on the Front and Rear Panels and connect to the Body Panel (M). The uppermost pole in the Body Panel should be turned with the connection downward. All other poles should be turned with the connection upward, as shown. Figure for Bar Installation (Steps 13-14) 13. Insert Rafter Bars (I) into the Sleeves at the top of the Body Panel (M). Insert Side Bars (J) into the Sleeves 14. at the sides of the Body Panel (M). Figure for Bar Connection (Steps 15-19) 15. Find the holes in the Bars (I, J) and line them up with the holes in the Poles (G, H). Secure the Bars (I, J) to the Poles 16. (G, H) using four Screws (R) per Bar. The Screws will be threaded directly through the cloth surrounding the Bars. Choose an area for the Greenhouse 17. that is flat, level and free of debris. If possible place the Greenhouse in an area that is sheltered from the wind. High winds can tear the Greenhouse loose from the Stakes (N) and could result in property damage or personal injury. In case of severe weather, take the Greenhouse apart. Examin...