Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Keep the hardware bags and their contents separate. If any parts are missing, call our Customer Service Department. **A MINIMUM OF TWO ADULTS ARE REQUIRED FOR ASSEMBLY** SAFETY INSTRUCTIONS Failure to follow these safety instructions may result in serious injury or property damage. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk of accident or injury. A high probability of serious injury exists if this display is not installed, maintained, or operated properly. • If using a ladder during assembly, use extreme caution. Follow all warnings and cautions on the ladder carefully. • 2 people are required for assembly. • Misuse could result in system failure. • If technical assistance is required, contact the manufacturer. Most injuries are caused by misuse and/or failure to follow instructions. Save this instruction in the event that the manufacturer has to be contacted for replacement parts. ** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at: 1 (800) 225-3865 Hours: Monday - Friday 9:00 a.m. to 5:00 p.m. (MST). Call, or visit our Web site for Saturday hours. PARTS LIST ID Reorder# Part # 1013592 CB12500 CB11000 1009258 117 CB11780C CB11700 ------- ------- ------- ------- ------- * Description Qty 108 ZS10882 Wall Panel 1 125 ZS12582 Window Wall Panel 1 110 1029724 Center Floor Panel 1 114 1009262 Lower Roof Panel 2 Center Roof Cap 1 AA 1009232 Skylight 1 AB 1021645 Roof Truss Channels 2 AC 1021644 Roof Truss Brace 1 AD 1021649 Roof Support 2 AE ZS01200 Window 1 1. 7/16” Wrenches (2) 2. 3/8” Wrenches (2) 3. #2 Phillips screwdriver or Electric drill with Phillips head Tools and Materials Required for Assembly (Not Included) Hardware Bag [1026292] TA 1021654 Truss Connector TB BB04500 Threaded Rod TD BN00300 1/4” Cap Nut TE BN01600 #10 Cap Nut TF BS06100 #10 x 3/8” Pan-Head Screw TH BS07500 .25” x .625” Screw TI BS05900 #10 x .5” Pan-Head Screw TJ BW01200 #10-1” Fender Washer TK 1007360 Window Latch 1 1 2 6 8 45 6 6 2 INSTRUCTION #1045398 8/25/2008 Part Numbers are listed when different from the Reorder Number. The Part Number will appear on most of the plastic parts. * AD 108 HARDWARE IS ACTUAL SIZE (Unless otherwise indicated) AA AB AC TA TB 117 TJ TDTE TI 110 125 TF TH AETK If you are Installing a New Shed 1. Check contents of boxes and compare to parts listed on the Parts List. 2. Follow instructions that came with your shed, but add extra floor panel, wall panels, Roof Cap and Skylight at appropriate points in the assembly. If you are Extending an Existing Shed 1. Remove any bolts or screws being used to anchor the shed to the ground. 2. Remove any objects from back shelves. 3. Remove any shelves, pegboards, or other objects hanging on the last two Side Wall Panels on either side. 4. Check contents of boxes and compare to parts listed on the Parts List. 5. Follow the steps in this manual. 6. If you are extending an 8’ x 5’ shed you will need to modify the following instructions by not removing as many parts as shown in the illustrations. 1 **Save all hardware for re-assembly!** a. Remove last three skylights. 2 a. Remove the back 3 roof caps. 3 a. Remove the back Roof panels and Roof support bars. 4 4 a. Remove the next Roof panels and Roof support bars. 5 a. Remove the Roof Truss. 6 a. Remove the last two Side Wall Panels. 6 a. Remove the last two Side Wall Panels. Note: If you’re adding onto a side entry shed, remove the panels (in gray) from the side of the shed rather than removing the back of the shed. If you’re adding on to both sides, remove the panels (in gray) from both sides of 7 a. Slide the back section of the shed away from the front. You will need to tip the back section forward slightly in order to disconnect the floor panels Be sure that there is nothing on the back shelves before moving the back section. One person should support the back wall while it is being tipped and moved. the shed (as illustrated), and follow the remaining steps. Assemble Window TF (1) a. Remove plastic sheeting from Window (AE) and slide Window into slot TH (4)on the Window Wall Panel (125). Attach a Window Latch (TK) above each corner of the Window as shown. When tightening screws (TH), be sure that Window Latches will slide freely. Do not overtighten. Insert screw (TF) TK (2) into the hole in the window. Set panel aside. AE Insert window with bent edge at top and pointing away from the wall. Place Screw (TF) in this hole to keep window from sliding up too far. Insert until flush with the window 9 9 a. Add new Floor Panel (110). Then, slide the back section into place and connect the floor panels (you will need to tip the panels forward slightly to connect the panels). 10 Tip up one floor panel and line up tabs and then lay floor panel flat. a. Add Wall Panels (108). Insert a wood block directly under the tab you want to insert, then slide block to next tab and repeat. Assemble Truss TF (6) TE (6) a. Atta...