Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
Using this line and a level, mark the remaining studs. (See Figs. A & B.) This will be the installed height of the shower base. Mix the low-shrink bedding material (grout, mortar, plaster, etc.). Concrete is not recommended. Apply enough bedding material to support the entire bottom of the shower base. The bedding material must not be used under the apron (front edge). 1 SHOWER BASE 3636.NEO 3838.NEO 4242.NEO 3232.ST 4834.ST 6034.ST 3636.ST 4242.ST 4832.ST 6032.STRH/LH* 5/16" ± 1/16" 3/8" ± 1/16" 5/16" ± 1/16" 3/8" ± 1/16" 1/4" ± 1/16" 1/4" ± 1/16" 1/4" ± 1/16" 5/16" ± 1/16" 1/2" ± 1/16" 1/2" ± 1/16" WASTE PIPE HEIGHT 2 3 4 5 6 A 51 mm (2) PVC Waste Pipe 127mmx127mm (5x5) Opening (See Product Chart for Drain Location) C/L C/L 3636.NEO, 3838.NEO, 4242.NEO 90° 90° 6-5/86-5/8 Insure the floor and stud walls are square and plumb. Provide a 5" x 5" (127mm x 127mm) opening in the floor for the drain (see Figs. A & B). The drain plug accom-modates a 2" (51mm) PVC waste pipe. The waste pipe should extend above the surface of the sub-floor, refer to chart on page 2 for the required dimensions. See product drawings on this page for the specified drain locations. B 3232.ST, 3636.ST, 4242ST, 6034.ST, 4834.ST, 4832.ST 90° 90° 51 mm (2) PVC Waste Pipe 127mmx127mm (5x5) OpeningC/L (See Product Chart for Drain Location) 6-5/8 Tape over the strainer to protect the finish and prevent construction debris from entering the drain. Finish installation as shown in Figure H. After the bedding material has been poured and before it sets, lower the shower base into position with the drain assembly sliding over the waste pipe as shown in Fig. E. It will be necessary to "rock" the shower base until the top of the tile flange aligns with the lines drawn in Step 3 on the stud walls. Make certain the apron is contacting the rough floor along the entire length of the shower base. Insure that the base is level in two directions (see Fig. F). Snap strainer back into place and check for proper drainage. Note: Variations in levelness of the subfloor may require adjustment of waste pipe height. * For 6032.STRH and 6032.STLH, see drawing for proper location of 5" x 5" drain cut-out. © AS America, Inc. 2008 751817-100 Rev. QFOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS. CLEANING AND MAINTENANCE D C E F G H DRAIN ASSEMBLY Strainer Drain Body Shower Base Silicone Sealant Rubber Gasket Fiber Gasket Locking Nut Rubber Caulking Gasket Lift and lower base over center of drain pipe and set into place Base Flange Drywall Screw Bracket Stud Shower Base Shower Base Splash Lip Flange Bracket Tile Adhesive Waterproof Drywall Tile Stud Caulk Your American Standard shower base is designed to last indefinitely with reasonable care and maintenance. The high-gloss acrylic surface is resistant to impact and retains its luster with proper care and maintenance. An integral, slip-resistant surface is incorporated for user safety. General Cleaning: Do not use abrasive cleaners; a mixture of warm w...
Este manual também é adequado para os modelos :Outros acessórios para a casa - Acrylic 3232.ST (63.59 kb)
Outros acessórios para a casa - Acrylic 3636.ST (63.59 kb)
Outros acessórios para a casa - Acrylic 3838.NEO (63.59 kb)
Outros acessórios para a casa - Acrylic 4832.ST (63.59 kb)