Assessments - 4, GPA: 4.5 ( )

Fabricante : Napoleon Fireplaces Arquivo Tamanho: 4.99 mb Arquivo Nome : Língua de Ensino:

figure 1 Room Volume = Length x Width x Height Max BTU/hr = Room Volume x 1000 . 50 If for example, the length of the rooms is 10 feet, the width of Room 1 is 10 feet, the width of Room 2 is 15 feet the height of the rooms is 8 feet. The volume of Room 1: 10 x 10 x 8 = 800 cubic feet. The volume of Room 2: 10 x 15 x 8 = 1200 cubic feet. If in this example a solid door separates Room 1 from Room 2, the volume of Room 2 could not be used. In this case the maximum BTU/h would be: Maximum BTU/h: 800 x 1000 = 16,000 BTU/h This would be considered a confined space since it can not support the 30,000BTU/h input of the heater and it would be necessary to provide adequate combustion and ventilation air to Room 1. In this example, because there is no door to the adjoining room, the volume of the adjoining room may be added to the volume of the room with the heater to get a total unconfined space. The total unconfined space: 800 + 1200 = 2000 cubic feet. Maximum BTU/h: 2000 x 1000 = 40,000 BTU/h If there are no more fuel burning appliances within this space then the 30,000 BTU/h input of the fireplace is suitable to be installed. This also assumes that the construction of this space is not unusually tight. 50 50 COMBUSTION & VENTILATION AIR PROVISIONS DETERMINING CONFINED OR UNCONFINED SPACE EXAMPLE 1 EXAMPLE 2 ROOM 2 ROOM 1 HEIGHTWIDTHLENGTHWARNING Barriers such as the bottom of a glass door frame placed in front of a gas log set can change the air flow characteristics of the fireplace which in turn can cause the unit to carbon or overheat and malfunction. Unvented gas heaters are a supplemental zone heater. They are not intended to be the primary heating appliance. Unvented gas heaters emit moisture into the living area. In most homes of average construction, this does not pose a problem. In houses of extremely tight construction, additional mechanical ventilation is recommended. During manufacturing, fabricating and shipping various components of this appliance are treated with certain oils, films or bonding agents. These materials may produce smoke and smells as they are burned off during the initial operation of the appliance; possibly causing headaches or eye or lung irritation. This is a normal and temporary occurance. Simply open a window to ventilate the room during the burn off period. INSTALLING IN A VENTED APPLICATION DAMPER STOP INSTALLATION The damper must be permanately locked in position to prevent full closure and to provide a minimum flue opening. Various methods for locking the damper may be used but may be restricted from region to region and it is important to know the specifics that apply to your area. For your convenience a damper stop is provided with the unit and may be used where not prohibited by state or local codes. Use the 3” adjustable bolt to adjust the damper to the correct opening, based on the enclosed chart. Should the damper stop not fit, or provide the required permanent opening from the Minimum Damper Opening table, have the damper cut to provide a minimum permanent opening or install an alternate stop. W415-0530 / 12.14.05 MINIMUM DAMPER OPENING (square inches) Chimney Height Masonry Fireplace Factory Built Fireplace 6 33.8" 8 31.2" 10 28.7" 22.1" 15 26.1" 17.3" 20 23.7" 14.5" 25 22.7" 12.6" 30 21.6" 11.3" 35 10.8" 40 10.2" Creosote, ashes and loose paint must be cleaned from the chimney flue and firebox by a qualified chimney cleaner, before installing in a solid fuel burning fireplace. Any outside air ducts and/or ash dumps in the fireplace shall be permanently closed at time of appliance installation. W415-0530 / 12.14.05 8 If heater shuts off, do not relight until you provide fresh air. If heater keeps shutting off, have it serviced. Keep burner and control compartment clean. When lit for the first time, the fireplace will emit a slight odour for a few hours. This is a normal temporary condition caused by the curing of the logs and the "burn-off" of internal paints and lubricants used in the manufacturing process and will not occur again. Open a window to ventilate the room during this burn off period. After extended periods of non-operation such as following a vacation or a warm weather season, the fireplace may emit a slight odour for a few hours. This is caused by dust particles burning off. In both cases, open a window to sufficiently ventilate the room. Purge the gas line with the glass door open. Assure that a continuous gas flow is at the burner before closing the door. CORRECT PILOT FLAME INCORRECT PILOT FLAME figures 32 MATCH LIGHTING INSTRUCTIONS 1. Remove any items necessary for easy access to the pilot (for example: logs, screens, etc.). 2. Follow appropriate lighting instructions found previously. Instead of pushing and releasing the piezo button, light a match and hold the flame to the end of the pilot and ignite the pilot. 3. After control knob has been released and pilot stays lit, reinstall any items that were removed for pilot access. 4. Call a qualified se...

Baixe o seu

Para fazer o download, introduza 2 dígitos :