Assessments - , GPA: ( )

Instruções de Operação Sterling Plumbing, Modelo Bypass Shower Doors 6075

Fabricante : Sterling Plumbing
Arquivo Tamanho: 1.9 mb
Arquivo Nome :

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

11. Install the Rollers -Outside Panel NOTE:The steel side of the roller must be installed against the top frame flange. Place the rollers on the top frame flange. The roller should face the bottom frame leg. Secure the rollers to the top frame flange with #8-32 x 3/8.hex washer head screws. Lay the outside door panel on a flat surface taking care to protect the glass. Cut two 7/8.(2.2 cm) long pieces of the provided adhesive tape. Remove the protective paper from the adhesive side of the tape and attach the tape to the bushings. Locate the bushings 1/4.(6 mm) from each end on the bottom frame of the outside panel. With the bushing tab toward the bottom frame groove, pinch the bushing legs together and push down until the bushing tab snaps into the bottom frame groove. Bushing Installed into the Bottom Frame Groove Bushing Roller Outside Panel Bottom Frame Leg Top Frame Flange #8-32 x 3/8" Hex Washer Head Screw #8-32 x 3/8" Hex Washer Head Screw Inside Panel Outside Panel Handle Side of Door Panel Side Frame Tab Tape Place the rollers on the top frame flange, facing the handle side of the door panel side frame. Secure the rollers with #8-32 x 3/8.hex washer head screws. 11. Install the Rollers -Outside Panel NOTE:The steel side of the roller must be installed against the top frame flange. Place the rollers on the top frame flange. The roller should face the bottom frame leg. Secure the rollers to the top frame flange with #8-32 x 3/8.hex washer head screws. Lay the outside door panel on a flat surface taking care to protect the glass. Cut two 7/8.(2.2 cm) long pieces of the provided adhesive tape. Remove the protective paper from the adhesive side of the tape and attach the tape to the bushings. Locate the bushings 1/4.(6 mm) from each end on the bottom frame of the outside panel. With the bushing tab toward the bottom frame groove, pinch the bushing legs together and push down until the bushing tab snaps into the bottom frame groove. Bushing Installed into the Bottom Frame Groove Bushing Roller Outside Panel Bottom Frame Leg Top Frame Flange #8-32 x 3/8" Hex Washer Head Screw #8-32 x 3/8" Hex Washer Head Screw Inside Panel Outside Panel Handle Side of Door Panel Side Frame Tab Tape Sterling 11 1035946-2-C 12. Install the Door Panels NOTE:Perform these installation steps from outside the bath/shower. Install the Inside Panel Lift the inside door panel with the rollers facing away from you. Position the rollers on the inside rail of the top track. Check the panel for proper alignment and smooth operation. Adjust as needed (directions below). Temporarily position the inside panel in the center of the top track. Adjusting the Rollers Remove the door panel. Loosen the roller screw(s) and move the roller(s) in the slot to align the panel. Tighten the screws and reinstall the panel. Install the Outside Panel Lift the outside door panel with the rollers facing you and position the rollers on the outside rail. Position the bottom of the door panel over the bottom track guide. Check the panel for proper alignment and smooth operation. If adjustment is needed, follow the adjustment directions above. Roller Outside of Bath/Shower Inside Panel Top Track Rail Side View Outside Panel Top TrackRail Inside of Bath Bottom Track Guide Side View Lift the inside door panel with the rollers facing away from you. Position the rollers on the inside rail of the top track. Check the panel for proper alignment and smooth operation. Adjust as needed (directions below). Temporarily position the inside panel in the center of the top track. Adjusting the Rollers Remove the door panel. Loosen the roller screw(s) and move the roller(s) in the slot to align the panel. Tighten the screws and reinstall the panel. Install the Outside Panel Lift the outside door panel with the rollers facing you and position the rollers on the outside rail. Position the bottom of the door panel over the bottom track guide. Check the panel for proper alignment and smooth operation. If adjustment is needed, follow the adjustment directions above. Roller Outside of Bath/Shower Inside Panel Top Track Rail Side View Outside Panel Top TrackRail Inside of Bath Bottom Track Guide Side View 1035946-2-C 12 Sterling Crimp here on each end. Bushing Bushing Inside Panel Guide Bushing Installed Inside Panel Guide Pile Seal Crimp here on each end. Bushing Bushing Inside Panel Guide Bushing Installed Inside Panel Guide Pile Seal Panel Frame Screw #8-18 x 3/8" Panhead Screw Screw Cover Inside Panel InsidePanel Guide Screw Cover 13. Install the Pile Seal Install a bushing into one end of the inside panel guide. Measure the length of the panel guide, subtract 1. (2.5 cm), then cut the pile seal to the resulting length. Slide the pile seal into the panel guide. Install a bushing into the other end of the panel guide. Use a pliers to crimp each end of the panel guide to keep the bushings from sliding off. 14. Install the Panel Guide NOTE: Perform these installation steps from insi...