Log:
Assessments - 3, GPA: 3.3 ( )

Instruções de Operação Dynasty Spas, Modelo Neptune Series

Fabricante : Dynasty Spas
Arquivo Tamanho: 184.13 kb
Arquivo Nome :
Língua de Ensino: en
Ir para baixar



Facilidade de uso


The LED lights will automatically turn themselves off after 2 hours in any one setting. Neptune Series Spas feature an easy-to-change selection of nine different LED color/display settings. To activate the LED lights, press the "LIGHT" button on the topside panel one time. To advance to the next color/display setting, press the "LIGHT" button twice in a row. The LED's will go off with the first press, then back on in the next setting with the second press. If the LED's remain off for more than 5 seconds, the color/display sequence will reset and start back at the beginning the next time the "LIGHT" button is pressed. The color/display sequence is: Setting #1 LED's light up and slowly cycle throught all six color. The slow cycle then restarts at the beginning and repeats. Setting#2 LED's light up and remain on in Aqua. Setting#3 LED's light up and remain on in Purple. Setting#4 LED's light up and remain on in Blue. Setting#5 LED's light up and remain on in Gold. Setting#6 LED's light up and remain on in Green. Setting#7 LED's light up and remain on in Red. Setting#8 LED's light up for 2 sec, flash off, then flash on in the next color, until all six colors have been displayed. The flashing cycle then restarts at the beginning and repeats. Setting#9 LED's flash on/off quickly, for a strobe light effect. The LED lights will automatically turn themselves off after 2 hours in any one setting. PROGRAMMING FILTER CYCLE DURAT ION The system automatically performs two filter cycles per day, at 12-hour intervals. During a filter cycle: • Pump 2 runs for one minute, then • Pump 1 runs at low speed for the programmed number of hours The "Filter Cycle" indicator lights up when the filter cycle is on. To set filter cycle duration: Press and hold Filter key Use Up or Down arrow keys When the desired setting is dis- until the display shows " xx", to change setting.played, press Filter key to confirm. representing the currently 0 = no filtration A filter cycle starts immediately. set filter cycle duration in 12 = continuous filtration hours. The filter cycle is suspended if the water temperature N.B.: After a power failure, the filter cycle duration raises more than 2 °F (1°C) above Set Point or if spa will return to its de fault value (2 hours). In this case, the first filter cycle will start one minute after power is in use (pumps and light started manually). The "Filte r" icon will blink (on 0.5 second, off 0.5 second, on 0.5 has been restored. second, off 1.5 seconds). TROUBLESHOOTING Pumps have started up for one Not a bug but a feature! minute on several occasions and "Filter Cycle" indicator is flashing. Our Smart Winter M odeprotects your spa from the cold by automatically turning pumps on for one minute several times a day to prevent water from freezing in pipes. 3 flashing dots are displayed. A problem has been detected. Do not enter the water! Check and open water valves. Clean filter if necessary. Check water level. Add water if needed. Shut power off and power your spa up again to reset the system. Call your dealer or service supplier if problem persists. Water temperature is flashing. Water temperature in the spa has reached 112 °F (44°C). Do not enter the water! Allow water to cool down. The system will reset automatically when water temperature reaches 109 °F (43°C). Call your dealer or service supplier if problem persists. The display is flashing. A power failure has occurred. Press any key to reset the system, then reprogram all desired...

Este manual também é adequado para os modelos :
Outros acessórios para a casa - 9919-100418-B (184.13 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias