4 B. step 1: * Attach 3 legs of the decorative stand to the large circular ring. Align threaded holes on the large ring with pre-drilled holes in the tops of the legs. Secure with alien head bolts, hand tighten for now. (See Fig. 4) * Now, attach smaller circular ring to middle brackets. Position ring into the channels. Align holes and apply alien head bolts and hand tighten at at this time ■ * Make sure all stand components are square to one another and the entire assembly is level with the floor. Then tighten all alien head bolts securely. * Locate Pure copper bowl & black steel grate. Position bowl onto leg assembly, ridge line on firebowl should be resting on upper rim of leg assembly. Make sure bowl is level & square with leg assembly. * Place steel grate onto bottom ridge of bowl so that it lays flat ■ C. Step 2: * Identify the 4 fire screen components and lav them out on the floor. Please make sure A, B, C, D four pieces of screens are available (the letter is also marked on screen). * Stack four screens, make sure screen A and B is above C and D , then insert the Handle through screen top hole by handle nut from inside of the screen . Do not over tighten. * Assemble A, B, C, D four screen’s bottom hole together, by using Screws and Nuts The screws must alwavs be fastened towards the inside of the screen assembly. You need one screw and nut to fasten two screen lids together. * Assemble four screen’s middle hole using the same method as * Tighten all bolts securely. D. Step 3: * Position assembled fire screen onto the fire bowl, centering it and making sure it is level. CAUTION: NEVER use your hands to remove or replace the screen when use the lift tool provided. Model #: Cocktail Firepit Series N Well traveled living HOME -GARDEN- PATIO *** Important Notice *** Do not return to place of purchase!! Please contact our Toll Free Hotline: (866) 985-7877 for customer service & warranty issues E Safety First!! Warning: For OUTDOOR USE only This is an outdoor patio firepit and should be placed in a safe, uncovered location away from combustible materials on all sides of the product. ★ ★ * * * * Do NOT leave open flames or embers unattended! * Do NOT allow children to be near open flames & fireplace * Do NOT burn EXCESSIVELY HOT fires! * Do NOT use during windy periods! * ALL METAL SURFACES WILL BE VERY HOT WHEN IN USE - DO NOT TOUCH! * ★ Do NOT use within 4 feet of any combustible materials or walls. Do NOT use in an enclosed, or covered location, or under tree branches The Spark Arrester, fire screen MUST be in place at ALL times during use. Use heat resistant gloves & lift tool when removing fire screen dome Always use the wrought iron stand provided when using the fireplace. NEVER place directly onto a wood floor/deck, near a wood fence or materials. If used over a wood deck, place a non-combustible material such as concrete pavers, stove-mat or hearth board directly beneath the fireplace to catch sparks & embers as well as protect the deck surface. Do not use flammable liquids, large amounts of wood pellets and/or multiple firelogs in the chiminea/fireplace which could produce extremely hot fires. Make sure there is plenty of ventilation completely surrounding the fireplace. Keep your fires reasonable. A fire that is too large or too hot can be very dangerous and could damage your fireplace. Although your firepit is considered a closed system , always comply witn all local laws, ordinances & statutes restricting the use of outdoor open flames in your community. Consult your local fire department. Always ensure that the fire is completely out before leaving your fireplace unattended. Smother any remaining embers with sand or water. Please use caution and common sense when burning in your firepit. Failure to adhere to the safety guidelines could result in fire damage to your deck, home or yard. Failure to exercise caution could also cause bodily injury or even death - so please be careful! Use heat resistant gloves & lift tool when removing fire screen dome p Lighting & Operating Fire screen - spark arrester dome MUST be in place at ALL times during use. * BEFORE you ignite your first fire \ * Place wood (no more than 3 large log pieces at a time), or firelog (no more than 1 at a time) in the center of the metal grate allowing for air flow between pieces and fireplace walls. * Use matches, butane lighters or electric starters. Do NOT use gasoline, kerosene, starter fluids or other flammable liquids that might cause a flash, high heat ignition fire. * Check and remove ash build up in the base bowl regularly. Web: Email: cservice@welltraveled.net Page l...
)
