Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Fasten each set together with one bolt in the center hole. 5 Set the assemblies use them later. aside. You will Rear Wall Angle 118 1/8" 3,0m Side Wall Angles 1115/8" 2,8m ® Parts Needed For O • 9294 Right Roof Beam (4) Roof Beam Assemblies • 9295 Left Roof Beam (4) Step 3 S_6 The roof beams join the two gables and support the roof panels. The main roof beam is made up of four pieces overlapped, back to back at the center. The left and right roof beam assemblies are made up of two pieces. 9295 __, Hint: These pieces are force-fitted, How.To Hentify Left and "_'_... _'_ Right so you may have to press hard to join Right Roof Beams "-_.:...._.... o;_ them together. "1 The figu re shows how to identify a 1137/16" 2,9m left and a right roof beam. As you will note, the difference is only which end of each beam has the six holes for joining the beams at the center. 2 Place the end of a right roof beam inside a left roof beam so that the six holes in each piece align. Make four sets of roof beams by repeating this p rocedu re. Do not insert bolts yet. 3 Take two of the pressed-together roof beams and join them as shown to form the main roof beam assembly. Hold the assembly together and fasten with 14 bolts and nuts. 1137/16" 4 Fasten the other two pressed6 2,9m together roof beams with 8 bolts to make the left and right roof beam assemblies. Single Beam Assembly 5 Set these pieces aside for later at Side of Roof assembly. 1137/16" 2,9m Main Roof Beam 1137/16" Doubled Beam Assembly at Peak 2,9m ® Parts Needed For ® o 6403DoorTrackSplice(1) Step 4 #oorTrack.e3e6DoorTrack(2) Assembly AI7 The door track assembly supports the sliding doors and reinforces the front wall. Iris made up of three pieces. 64O3 NOTE: Door Track Splice (painted part) 1 Using the door track splice, (painted), join the door track (galvanized) pieces end-to-end as shown. 2 Insert four screws from the underside only. Hint: The holes in the top side of the door track assembly are for fastening the gable to the top of the front wall in a later step. 3 Position door slides onto the , legs, from the end of door track END VIEW _ 66769 Q Parts Needed For e • Front Floor Assembly (1) • Side Floor Assembly (2) Step 5 Floor Frame • Rear Floor Assembly (1) "1 Assemble the four corners of the floor frame using two screws at each corner as shown. At the front corners fasten bolts through from the bottom with nuts on top. 2 Measure the floor frame diagonally. When the diagonal measurements are equal, the floor frame is square. NOTE If using a wood platform or concrete slab do not fasten the floor frames to your base at this time. You will anchor the building after it is erected. NOTE If you have purchased a Floor Frame Kit you need to install it at this time. When Diagonal Measurements are Equal the Floor Frame is Square. ® Parts Needed For ® ® 8995 Wall Panel (2) • 9372 Front Wall Panel (2) Step 6 Corners Q 9156 Corner Panel (4) UNI9 NOTE The remainder of the building assembly requires many hours and more than one person. Do not continue beyond this point if you do not have enough time to complete the assembly today. A partially assembled building can be severely damaged by light winds. Wide Side Narrow Each quires screw and a washer. bolt in the wall re" 1 Position a corner panel at the corner of the floor frame as shown. The widest part of each corner panel must be placed along the side of the building for all four corners. Fasten the corner panel to the floor frame with four screws. 8995 Support the corner panel with a step ladder until a wall panel is attached. 2 Attach the front wall panels to the front corner panels, as shown. A small gap will exist between front wall panel and ramp. 3 Attach the wall corner panels, as panels shown. to the rear 9372 8995 8995 Crimped Rib Underneath 4. Double-check the wall panels, the part numbers of before proceeding. #8-32 Hex Nut Washer IThe floor frame must be square I 9372 Panels rest on frame as shown #8Ax5/16"Sclew 0 Door Track Assembly (1) O Parts Needed For O ORearWallAngleAssembly(1) St p 7e Frames , Side Wail Angle Assemb,ies (2)• Rear Wall Channel Assembly (1) s2o O Side Wall Channel Assemblies (2) The main frame pieces give rigidity to the side walls and provide a surface for attaching the gables which support the roof. 1 Fasten the rear wall angle assembly across the inside top of the rear wall using screws. 2 Fasten the rear wall channel assembly across the middle of the rear wall using screws. 3 Fasten the sidewall angles across the inside top of the side panels using screws. Side wall angles must overlap rear wall angle in corners. 4. Fasten the side wall channel assemblies across the middle of the side panels using screws. Fasten overlaps in rear corners with screws. 5 Fasten the door track assembly (holes on top) across the top of the front wall panels using screws. See the figu re. 9366 \ l _on t """_..-.,_ _ Long Leg Top Opening Facing in Short Leg on Bottom The wall NOTE channels behind the front wa...
Este manual também é adequado para os modelos :Outros acessórios para a casa - 697.68101 (1.91 mb)
Outros acessórios para a casa - SC1010 (1.91 mb)