Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
INSTRUCTION #1026972 **A MINIMUM OF TWO ADULTS ARE REQUIRED FOR ASSEMBLY** BEFORE BEGINNING ASSEMBLY Identify and inventory all parts using the checklist boxes on the Parts List. Keep the hardware bags and their contents separate. If any parts are missing, call our Customer Service Department. SAFETY INSTRUCTIONS Failure to follow these safety instructions may result in serious injury or property damage. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk of accident or injury. A high probability of serious injury exists if this display is not installed, maintained, or operated properly. • If using a ladder during assembly, use extreme caution. Follow all warnings and cautions on the ladder carefully. • 2 people are required for assembly. • Misuse could result in system failure. • If technical assistance is required, contact the manufacturer. Most injuries are caused by misuse and/or failure to follow instructions. PARTS LIST AA 1020443 Center Roof Cap 1 AB 1019503 Gutter Channel 2 AC 1007977 Wall Support Channel 2 AD 1007988 Truss Channel 1 AE 1007996 Inner Roof Panel 2 AF 1007997 Wall Panel 2 AG 1009232 Skylight 1 AJ 1008000 Inner Floor Panel 2 AK 1008001 Roof Support Strip 4 AM 1020423 Truss Support Strip 2 Shed Parts Box [1019238] Skylight Hardware Bag [1011616] 1 LA BW01200 #10-1” Fender Washer 7 LB 1010132 #10 x 5/8” Pan Head Screw 7 Truss Extension Hardware Bag [1016014] 1 FA 1009117 Floor Bracket 2 FB 300072 1/4” x 1 1/2” Hex Bolt 11 FC BN00300 1/4” Cap Nut 11 FD 1012933 Center Gutter Connector 1 Shed Screw Hardware Bag [1011615] 1 SS BS07500 1/4” x 5/8” Screw 60 LB LA FA FB SS FC FD Tools and Materials Required for Assembly (Not Included) 1. 7/16” Wrenches (2) 2. 3/8” Wrenches (2) 3. #2 Phillips screwdriver or Electric drill with phillips head HARDWARE IS NOT ACTUAL SIZE (unless otherwise indicated) AG AF AE AA AJ AK AM AB AC AD If you are Extending an New Shed 1. To obtain instructions for extending a new shed, contact our Customer Service Department. To extend a never assembled shed, Call Customer Service for Instructions: 1 (800) 225-3865 Site Selection a. This extension kit adds another 30” to the length of your shed. Before beginning expansion of your shed be sure that your site can accomodate the new size. Option 2: Add Extension Kit to an Existing Shed **Save all hardware for re-assembly!** ATTENTION: If your existing shed is anchored to the ground, remove all anchoring hardware before following these steps. Opt. 2.1: Remove the four Lower Roof Panels and two Center Roof Caps (leave Skylights in place) that are highlighted below. Note: Your shed may be shorter than shown above. Skip the very back Roof Panels (slightly more narrow than the middle Roof Panels) and then remove the next two Roof Panels from each side of the shed (along with the connected Roof Caps). Repeat Steps 2.2 through 2.4 for both sides of the shed. Opt. 2.2: Remove all screws from the highlighted Wall Panel that connect it to adjoing Wall Panels and to the Wall Support. Remove this panel. Remove this panel. Opt. 2.3: Tip the Wall Panel inward. Note: To remove a Wall Panel, slide it to the left (when looking at it from inside the shed) until it lifts out. Opt. 2.4: Use a long flat screwdriver to gently pry the bottom corner of the Wall Panel so that it has room to slide on the inside of other Wall Panels. Slide the Wall Panel to the left, and then remove the panel. Note: As you remove the Wall Panels, have one person support the Truss assembly so that it does not fall over. Opt. 2.5: Remove the Truss assembly and set it aside for later. Opt. 2.6: With at least on person on each side of the shed, tip the back section of the shed forward to about a 45 degree angle and slide the back section away from the shed.. Opt. 2.7: Fit together the two Inner Floor Panel extensions (AJ). AJ AJ Opt. 2.8: Connect the Inner Floor Panel extensions (AJ) to the other Inner Floor Panels on the main section of the shed. Opt. 2.9: With at least on person on each side of the shed, tip the back section of the shed forward to about a 45 degree angle and slide it forward to re-connect it to the rest of the shed. Opt. 2.10: Fit two Truss Support Strips (AM) together. Bolt Truss Support Strips (AM), Center Gutter Connector (FD) and two Gutter Channels (AB). Refer to the Owner’s Manual that came with your shed when assembling other truss frames. AM AM FB AB Finger Tighten Hardware FC WARNING AB Do not overtighten the Cap Nut. If the end of the Bolt breaks through the plastic cap, call our Customer Service Department at the number on Page One. Exposed threads on the end of the Bolt may cause serious injuries. AM Opt. 2.11: Attach a Gutter Channel (AB) (Truss Support Strips (AM) fit inside Gutter Channel (AB)). Attach Truss Channel (AD) to Gutter Channel (AB) at each end. AM (x2) FC AB FB AB AB FC FD FB Tighten All Hardware Opt. 2.12: Attach Truss Assembly to two Wall Support Channels (AC). Do not co...